where i put the turrometre on board

alexromania · Post by **alexromania** » Fri Mar 26, 2010 5:23 pm

helo, somebody knouws where i put the turometre on board , on a bx serie 1 1.9 diesel, with leds turometre, that band who mesure the rotatins

alexromania · Post by **alexromania** » Fri Mar 26, 2010 5:25 pm

please a picture or a electrical scheme

Post by **docchevron** » Fri Mar 26, 2010 9:01 pm

Ok, erm, I *think* you mean the sensor for the Rev counter?

In which case it's down the back of the engine and sticks through the rear plate facing the flywheel.

Some early ones had the sensor located in the top of the bell housing (like the petrol CAS)..

Unless you mean something quite different!

alexromania · Post by **alexromania** » Fri Mar 26, 2010 9:05 pm

sorry i don't know very whelle english. I whant to mean where i put on dashboard, a picture with the scheme electric

alexromania · Post by **alexromania** » Fri Mar 26, 2010 9:06 pm

i have the sensor on top of the engine, but where i put it on dashboard

Post by **docchevron** » Fri Mar 26, 2010 10:52 pm

Ahh, I'm with you, no problem mate, your English is infinitely better than my Romanian!

What year is the car? Is it a Mk1, or a Mk2?
I assume Mk1, in which case I believe the rev counter was a strip light at the bottom of the instrument binnacle?

alexromania · Post by **alexromania** » Sat Mar 27, 2010 6:33 am

my car is a mk1, a have some picture with she
http://img42.imageshack.us/img42/5645/img0091l.jpg,
and with the dashboard
http://img718.imageshack.us/i/spa1062.jpg/
http://img708.imageshack.us/i/spa1061.jpg/

alexromania · Post by **alexromania** » Sat Mar 27, 2010 6:35 am

http://img42.imageshack.us/img42/5645/img0091l.jpg
http://img714.imageshack.us/img714/6790/img0142za.jpg

alexromania · Post by **alexromania** » Mon Mar 29, 2010 5:55 am

nobody can"t help me??

toddao · Post by **toddao** » Mon Mar 29, 2010 7:52 pm

Hello Alex,

I'm sure someone can help you - I have the same car as you. Can you post your question in Romanian and then it might be easier to understand?
One of our members - TB2 - can speak Romanian and English and can hopefully translate your question correctly.

alexromania · Post by **alexromania** » Mon Mar 29, 2010 8:27 pm

oo yes i can do that.
problema mea este in felul urmator, eu am un bord cu turometru cu leduri, am senzorul pe cutia de viteze, si am si o mufa pe bord. problema este ca nu stiu unde se pune in bord, in ce pini din bord.

Simon B · Post by **Simon B** » Mon Mar 29, 2010 10:20 pm

Google Translate does a good job of that. It looks like he wants to know how to wire up a Phase 1 LED rev counter.

alexromania · Post by **alexromania** » Tue Mar 30, 2010 6:55 am

up is a picture who show how look is the dashboard for boughts side's. in back of dashboard where i connect the wires, i whant to know where i put the wiers,

toddao · Post by **toddao** » Tue Mar 30, 2010 7:25 am

Ok, so it is understood already - we don't need TB2 to translate!

I would have to remove my dash and take a photo to be able to give you an answer Alex. I will try this weekend.

alexromania · Post by **alexromania** » Tue Mar 30, 2010 8:21 am

THANKS MAN, THIS WEEKEND IS THE EASTER IN ROMANIA, AND I'M NOT GONA BE IN THE FRONT OF MY COMPUTER BUT I'LL RECEIVE THE MESSAGE, THANKS FOR YOU TIME.HERE IN ROMANIA DON'T FIND THIS PEOPLE WHO ANSWER IN THIS SHORT TIME LIKE YOU DID.THANKS AGAIN. IF YOU WHANT TO SPEAK ANOTHER TIME I GIVE YOU MY EMAIL ADRESS ALEXUTZU_YOD@YAHOO.COM, AND MY MESSENGER ADRESS ALEXUTZU[/b]