Breaking fault
Breaking fault
Hi ....anyone got any thoughts on this? I eventually get round to changing the front subframe on my 1991 turbo after it cracked. The car has patiently waited two years for me to do this standing unused! However..... I replaced front arms and links while I was at it and also two front to rear pipes ( they haven't got mixed up). Well the suspension is fine.... But the breakers are dangerous.... There is a strange delay as I press the break pedal,,,,,, nothing happens then they come on like mad and nearly throw you thru the windscreen. I suspect the rears are hardly working at all..... The discs are/were new. The fronts are nice and shiny...... The rears making progress......and thoughts as to the cause of this dangerous delayed breaking?
Bx turbo diesel 1989
Bx 1.9 Rd estate 1989
Citroen Light 15 1952
Bx 17 TZD diesel turbo 1992
Xantia 1.8 16v
Bx 1.9 Rd estate 1989
Citroen Light 15 1952
Bx 17 TZD diesel turbo 1992
Xantia 1.8 16v
- Jaba
- 1K Away
- Posts: 1897
- Joined: Tue Jul 05, 2005 7:54 am
- Location: Usually in the garage
- My Cars: BX GTi, C3 Auto
- x 82
Re: Breaking fault
Air in the system would behave this way. Have you tried lots of citaerobics to dispel all air in the system and then bleeding all the front and rear brake lines ?
The Joy of BX with just one Citroën BX to my name now. Will I sing Bye Bye to my GTI or will it be Till death us do part.
Re: Breaking fault
Difficult to say exactly what is causing that problem. I suspect I would look at the following. Bleed the hydraulic system with relief valve. Bleed front brakes, and rears to get clean fluid through the brake system. Ensure Accumulator sphere is in good condition. Check calipers are not partially seized, and pedal travel not obstructed. Renew fluid (LHM) if old, it may have become a bit hydroscopic (not as bad as Dot 4 Stuff mind). Finally the FDV may be faulty, it's on or near the nearside rear of the front subframe.
- JayW
- 1K Away
- Posts: 1590
- Joined: Thu Dec 07, 2006 6:40 pm
- Location: Now listen here you mullet...
- x 13
Re: Breaking fault
The "relief" valve does not bleed anything, it just releases system pressure, IT MUST remain done up when bleeding.
The FDV is bolted to the front of the gearbox with the regulator and does not affect brake or suspension pressure, only the steering. The thing at the back of the sub frame is the safety/security valve.
I would also agree that air in the system or a doseur fault are most likely providing all the pipework went back on properly.
The FDV is bolted to the front of the gearbox with the regulator and does not affect brake or suspension pressure, only the steering. The thing at the back of the sub frame is the safety/security valve.
I would also agree that air in the system or a doseur fault are most likely providing all the pipework went back on properly.
I have zero patience for your tedium.
Re: Breaking fault
To up date you for further help! I have bled the front brakes no problem..... Fluid comes out easy...... No fluid however comes out of the rear.... I have even disconnected a pipe at the off side rear caliper..... No fluid! This was done on a garage two poster lift with the engine running, with the wheels suspended if it makes any difference. I have driven the car ( on trade plates) some twenty miles (very carefully) ..... No change..... I have re piped whole bx s in the past with no problem..... Any more ideas?
Bx turbo diesel 1989
Bx 1.9 Rd estate 1989
Citroen Light 15 1952
Bx 17 TZD diesel turbo 1992
Xantia 1.8 16v
Bx 1.9 Rd estate 1989
Citroen Light 15 1952
Bx 17 TZD diesel turbo 1992
Xantia 1.8 16v
- JayW
- 1K Away
- Posts: 1590
- Joined: Thu Dec 07, 2006 6:40 pm
- Location: Now listen here you mullet...
- x 13
Re: Breaking fault
Bleeding the rears with the wheels suspended can be problematic.
They are fed by the pressure in the rear suspension (the higher the load, the greater the pressure and the greater the braking force), suspending the wheels all but cuts off fluid supply.
You really need to try with the cars weight on them (4 post or pit).
That being said, you should still get SOMETHING through. Sounding increasingly like a doseur issue.
They are fed by the pressure in the rear suspension (the higher the load, the greater the pressure and the greater the braking force), suspending the wheels all but cuts off fluid supply.
You really need to try with the cars weight on them (4 post or pit).
That being said, you should still get SOMETHING through. Sounding increasingly like a doseur issue.
I have zero patience for your tedium.
-
- Over 2k
- Posts: 2695
- Joined: Sun Sep 02, 2012 9:54 pm
- Location: South Lincs
- My Cars: 90 Bx Tzd turbo ven red 295k
74 D Super 5 black
05 Volvo V50 2.0d 180k
65 Peugeot Boxer work van 280k - x 137
Re: Breaking fault
I'd go with the faulty doseur valve, not uncommon for them to fail.
90 BX Tzd turbo 294k SORN undergoing major surgery
90 BX Tzd turbo estate 46k awaiting surgery
65 Peugeot Boxer Van the new workhorse
52 Toyota Rav4 180k Bulletproof Jap reliability
90 BX Tzd turbo estate 46k awaiting surgery
65 Peugeot Boxer Van the new workhorse
52 Toyota Rav4 180k Bulletproof Jap reliability
Re: Breaking fault
I can look at this tomorrow.......but...... Doseur valve? Where is it located?
Bx turbo diesel 1989
Bx 1.9 Rd estate 1989
Citroen Light 15 1952
Bx 17 TZD diesel turbo 1992
Xantia 1.8 16v
Bx 1.9 Rd estate 1989
Citroen Light 15 1952
Bx 17 TZD diesel turbo 1992
Xantia 1.8 16v
-
- Over 2k
- Posts: 5917
- Joined: Wed Dec 16, 2009 8:02 pm
- Location: Harwood, Bolton
- My Cars: Land Rover Discovery Series 1 200tdi 3 door
Land Rover Discovery Series 2 Facelift TD5
2020 Fiat Panda cross 4x4 twin air. - x 27
Re: Breaking fault
As said by Jay you can't bleed the rear brakes with the wheels suspended, some even put a heavy load in the back to increase the fluid flow through the load sensing.
Kevan
1997 Mercedes C230 W202
2003 Land Rover Discovery Series 2 Facelift TD5 - Daily driver / hobby days and camping.
1993 Land Rover Discovery 200tdi Series 1 3 door - in need of TLC
2020 Fiat Panda 4x4 Cross Twin Air.
1997 Mercedes C230 W202
2003 Land Rover Discovery Series 2 Facelift TD5 - Daily driver / hobby days and camping.
1993 Land Rover Discovery 200tdi Series 1 3 door - in need of TLC
2020 Fiat Panda 4x4 Cross Twin Air.
Re: Breaking fault
BTW I thought it was meant to be spelt Braking rather than Breaking, the former preferable for a BX rather than the latter...
-
- Confirmed BX'er
- Posts: 52
- Joined: Wed Oct 21, 2015 11:45 pm
- Location: Chichester
- My Cars: 1992 BX19TGD ESTATE 178k
2014 Fiat Ducato Sportivo - x 1
Re: Breaking fault
The doseur valve is mounted low down on the bulkhead in the engine bay. It's on the drivers side (assuming right hand drive). The bolts that hold it in place are actually inside the car behind the brake pedal.Alastair wrote:I can look at this tomorrow.......but...... Doseur valve? Where is it located?
Re: Breaking fault
It still sounds like air in the system to me.
The doseur valve is the Citroen equivalent of the brake master cylinder.
To bleed the brakes properly, you need to press & HOLD the brake pedal down, undo the bleed screws on the front callipers until all the air comes out of them.
It is the same principal for the rears, only you need some weight on the back axle. If you use a 2 post ramp, then you will need a stand (such as a transmission jack) under a rear arm, and then proceed with bleeding. The rears will take longer to bleed as the pipe is in effect, twice the length of the car.
I made the same mistake with the rear brakes the first time I tried to bleed mine, not understanding how the system worked. With weight on the axle it will send LHM out.
Hope that helps.
The doseur valve is the Citroen equivalent of the brake master cylinder.
To bleed the brakes properly, you need to press & HOLD the brake pedal down, undo the bleed screws on the front callipers until all the air comes out of them.
It is the same principal for the rears, only you need some weight on the back axle. If you use a 2 post ramp, then you will need a stand (such as a transmission jack) under a rear arm, and then proceed with bleeding. The rears will take longer to bleed as the pipe is in effect, twice the length of the car.
I made the same mistake with the rear brakes the first time I tried to bleed mine, not understanding how the system worked. With weight on the axle it will send LHM out.
Hope that helps.
1992 Citroën BX 1.9 Diesel Meteor 4x4 - The Project.
1992 Citroën BX 1.9 TXD (with GTI engine; Mulleys old car) - Parts car.
2004 Citroën Xsara Desire. (Now gone).
2016 Ford Focus Zetec - Daily Driver. (Absolute bone shaker).
1992 Citroën BX 1.9 TXD (with GTI engine; Mulleys old car) - Parts car.
2004 Citroën Xsara Desire. (Now gone).
2016 Ford Focus Zetec - Daily Driver. (Absolute bone shaker).
-
- Over 2k
- Posts: 2695
- Joined: Sun Sep 02, 2012 9:54 pm
- Location: South Lincs
- My Cars: 90 Bx Tzd turbo ven red 295k
74 D Super 5 black
05 Volvo V50 2.0d 180k
65 Peugeot Boxer work van 280k - x 137
Re: Breaking fault
The rear brakes take pressure from the rear spheres as a supplement i.e the more weight you have on the back end the more pressure is applied to the rear brake calipers so effectively wheels off and rest the hubs on blocks of wood (this is how i do it) as if the rear end is "loaded".
90 BX Tzd turbo 294k SORN undergoing major surgery
90 BX Tzd turbo estate 46k awaiting surgery
65 Peugeot Boxer Van the new workhorse
52 Toyota Rav4 180k Bulletproof Jap reliability
90 BX Tzd turbo estate 46k awaiting surgery
65 Peugeot Boxer Van the new workhorse
52 Toyota Rav4 180k Bulletproof Jap reliability
Re: Breaking fault
Thanks David.... I have had BXs for 20 years and never had an issue after piping.... But your advice sounds good as does rutter123.... I can proceed along these lines with hope..... Will report back...... Much better than silly Snyd comments about spelling!!!
Bx turbo diesel 1989
Bx 1.9 Rd estate 1989
Citroen Light 15 1952
Bx 17 TZD diesel turbo 1992
Xantia 1.8 16v
Bx 1.9 Rd estate 1989
Citroen Light 15 1952
Bx 17 TZD diesel turbo 1992
Xantia 1.8 16v
Re: Breaking fault
Alastair wrote: Much better than silly Snyd comments about spelling!!!
Oh Dear....