Knocking noise from front suspension.
Knocking noise from front suspension.
I have a knocking noise from somewhere underneath the front which seems to be suspension related as it`s when going over bumps that it`s most noticeable.
Just had the spheres re-gassed but this noise was there before and hasn`t gone away.
I`m sure on the receipt for the spheres it mentioned something about a stiff strut(?) but I`ve lost the receipt now.
I also have a high pitched squeek from the o/s/f wheel which only goes at low speeds or when turning the steering wheel. Is it fair to assume it`s the wheel bearing and what kind of job is it to do please?
Any help much appreciated, thank`s.
Just had the spheres re-gassed but this noise was there before and hasn`t gone away.
I`m sure on the receipt for the spheres it mentioned something about a stiff strut(?) but I`ve lost the receipt now.
I also have a high pitched squeek from the o/s/f wheel which only goes at low speeds or when turning the steering wheel. Is it fair to assume it`s the wheel bearing and what kind of job is it to do please?
Any help much appreciated, thank`s.
-
- 1K Away
- Posts: 1604
- Joined: Wed May 18, 2005 6:23 pm
- Location: North Wales
Wheelbearings need a fly press to get them out/in mine were very loudly grinding but had no play, both inner tracks had cracks in them, might as well do the balljoints while the hub carriers are off then relax....... and wait for the next thing
Stewart
Stewart
TZD 19 TD one of the few
Xantia Td estate, going soft
Xantia Td estate, going soft
First of all many thanks for the replies. Hadn`t noticed the noise in reverse and it`s more of a clonk than a bang or a knock to be more accurate.
The car drives and steers well apart from that and the more I think about it the more I`m sure the receipt for the re-gas said the strut was tight whatever that means.
It was doing this a bit before the fairly recent last MOT and the o/s/f ball joint was knackered which I hoped would stop when I had it done for the MOT but alas not.
The car drives and steers well apart from that and the more I think about it the more I`m sure the receipt for the re-gas said the strut was tight whatever that means.
It was doing this a bit before the fairly recent last MOT and the o/s/f ball joint was knackered which I hoped would stop when I had it done for the MOT but alas not.
-
- 1K Away
- Posts: 1604
- Joined: Wed May 18, 2005 6:23 pm
- Location: North Wales
Have you done the internal LHM lube thing yet? I did mine and it made a big difference but the car still creaked and jumped a little when rising, the eventual cure was to soak strips of towelling in gear oil and wrap them round the strut "slider" under the gaiter, now things are smooth.
Stewart
Stewart
TZD 19 TD one of the few
Xantia Td estate, going soft
Xantia Td estate, going soft
Cheers for that, now time for me to appear a little dim! Can you please explain in layman`s terms exactly where the strut slider is? I have reasonable mechanical knowledge but I`m not the greatest spannerman in the world!Stewart (oily!) wrote:Have you done the internal LHM lube thing yet? I did mine and it made a big difference but the car still creaked and jumped a little when rising, the eventual cure was to soak strips of towelling in gear oil and wrap them round the strut "slider" under the gaiter, now things are smooth.
Stewart
Bx suspension
Cheers for that, now time for me to appear a little dim! Can you please explain in layman`s terms exactly where the strut slider is? I have reasonable mechanical knowledge but I`m not the greatest spannerman in the world!Stewart (oily!) wrote:Have you done the internal LHM lube thing yet? I did mine and it made a big difference but the car still creaked and jumped a little when rising, the eventual cure was to soak strips of towelling in gear oil and wrap them round the strut "slider" under the gaiter, now things are smooth.
Stewart
-
- 1K Away
- Posts: 1604
- Joined: Wed May 18, 2005 6:23 pm
- Location: North Wales
Raise the car up to max height, reach over top of front wheel and slide the corrugated plastic gaiter upwards, when its high enough you will feel the smooth part of the strut going into the body of the strut, the oily towelling needs wrapping around the smooth bit and then pull the gaiter back down.
Stewart
Stewart
TZD 19 TD one of the few
Xantia Td estate, going soft
Xantia Td estate, going soft
Cheers, do I then leave the oily towelling in place or just put on for a short while and then remove?Stewart (oily!) wrote:Raise the car up to max height, reach over top of front wheel and slide the corrugated plastic gaiter upwards, when its high enough you will feel the smooth part of the strut going into the body of the strut, the oily towelling needs wrapping around the smooth bit and then pull the gaiter back down.
Stewart
Sorry if that sounds daft!
-
- Citroen Sorceror
- Posts: 1266
- Joined: Fri May 20, 2005 8:51 pm
- Location: straddling the channel
- My Cars: 2003- Passe-Partout 1.9 TGD estate
2005 Grolliffe Tizzydee turbo estate and sundry other BXs and Grace, a CX TRD.
2008 to 2023 - all sorts of stuff, some interesting
2024. TxD 1.9D estate. 'Wheelybin' - x 12
-
- BXpert
- Posts: 546
- Joined: Sat Jun 25, 2005 7:26 pm
- Location: Bristol.UK.
Knocking noise from front.
Hello my son had the same thing Drop links he said with great confidence, so did I. They were changed in a flash, well sort of, road test everything fine.
Next day Clunk--clunk. B***s. Silly wheel loose, strut, track rod end no.Nine months before both bottom ball joints had been replaced and one of them had a conciderable amount of play, not just a little bit, the I am going to separate job. I am not so sure about quality control these days, bring back nipples I say. Enough of that I must not get excited.
So perhaps a check on the bottom ball joints might be a good idea.
Cheers.
Geoff.
Next day Clunk--clunk. B***s. Silly wheel loose, strut, track rod end no.Nine months before both bottom ball joints had been replaced and one of them had a conciderable amount of play, not just a little bit, the I am going to separate job. I am not so sure about quality control these days, bring back nipples I say. Enough of that I must not get excited.
So perhaps a check on the bottom ball joints might be a good idea.
Cheers.
Geoff.
Re: Knocking noise from front.
I have a pair - seem supurfluous to requirements.Geoffrey Gould wrote:bring back nipples I say. Cheers.
Geoff.
Ahh , heady days going round my BLMC motors with a grease gun. Now all I ever get to use it on is the caravan. It was a shock when I got my first Fraud Fiasco and found no grease points I can tell you, I thought "what will I do with my Sunday mornings now?"
-
- BXpert
- Posts: 546
- Joined: Sat Jun 25, 2005 7:26 pm
- Location: Bristol.UK.
Knocking noise from front.
Hi Marty well carying on from knocking er knockers how about a bit of nipple polishing?
OK Ile go away now.
Best.
Geoff.
OK Ile go away now.
Best.
Geoff.
- Vanny
- Merseyside resident
- Posts: 3581
- Joined: Tue May 17, 2005 11:48 pm
- Location: BXProject
- My Cars: BX 16v Ph2 - Jazz
BX 16v Ph2 - XPO - x 79
- Contact:
Re: Knocking noise from front.
I've got two and a half!Marty wrote:I have a pair - seem supurfluous to requirements.Geoffrey Gould wrote:bring back nipples I say. Cheers.
Geoff.