Mat's BX Blog

Tell us about life with your BX, or indeed life in general!
Post Reply
User avatar
mat_fenwick
Moderator
Posts: 7326
Joined: Tue Sep 20, 2005 4:08 pm
Location: North Wales
x 19

Post by mat_fenwick »

Vanny wrote:we went to bed awefully early!
In my case (if I remember correctly), completely against my will! Although probably for the best...
Image

1993 1.9 TZD Turbo Estate
1996 3.9 V8 Discovery
1993 VW LT35 campervan
1985 Hyundai Stellar V8
2016 Hyundai iLoad
User avatar
docchevron
The Immoderate half of the admin team
Posts: 7524
Joined: Sun Jun 04, 2006 7:03 pm
Location: A Bucket of Fish
x 7
Contact:

Post by docchevron »

:lol: :lol: :lol:

I think you'd have kept going until there was nothing left in the whole universe to drink!

True Vanster, it was an early night for us, but it was a good deal colder than previous years...
Smokes lots, because enough's enough already!

Far too many BX's, a bus, an ambulance a few trucks, not enough time and never enough cash...
User avatar
mat_fenwick
Moderator
Posts: 7326
Joined: Tue Sep 20, 2005 4:08 pm
Location: North Wales
x 19

Post by mat_fenwick »

Managed to find a replacement head, which I have now fitted. The genuine Citroen head bolts I found were actually for a 1.8 petrol Xantia, and about 10mm too long, which was a bit of a pain. Fortunately the old bolts were still within spec. for length, so (reluctantly) I re-used them, as I didn't want the job to drag into this week. I was pleased to notice that honing marks were still visible in the bores, with no wear ridge after 156k miles.
The first start is here.

I also replaced 2 of the 3 braided hoses behind the engine, a little easier to do with the head off. A new accumulator has gone on, and the HP pump is next on the list. I've still got the new radiator to fit; also a new rear strut and an inner CV boot, which I noticed is a bit flaky. I've got a set of rear pads and discs which I may stick on if I get chance.
Then after that it needs a MOT and a puncture repaired before it'll be ready for France, I might even get chance to take it for a test run first!
Image

1993 1.9 TZD Turbo Estate
1996 3.9 V8 Discovery
1993 VW LT35 campervan
1985 Hyundai Stellar V8
2016 Hyundai iLoad
User avatar
mat_fenwick
Moderator
Posts: 7326
Joined: Tue Sep 20, 2005 4:08 pm
Location: North Wales
x 19

Post by mat_fenwick »

Getting there slowly - this evening saw the inlet manifold going back on, HP pump replaced, new radiator in and driveshaft out ready for a new boot tomorrow. Then darkness stopped play...

Can't believe how lucky I've been with the weather - it's rained once in the last 3 weeks! Most unlike Wales.
Image

1993 1.9 TZD Turbo Estate
1996 3.9 V8 Discovery
1993 VW LT35 campervan
1985 Hyundai Stellar V8
2016 Hyundai iLoad
User avatar
Vanny
Merseyside resident
Posts: 3581
Joined: Tue May 17, 2005 11:48 pm
Location: BXProject
My Cars: BX 16v Ph2 - Jazz
BX 16v Ph2 - XPO
x 79
Contact:

Post by Vanny »

thats a damn sight more rain than i've had here, my garden is looking drier than the moon!
User avatar
MULLEY
Over 2k
Posts: 8406
Joined: Thu Jun 22, 2006 11:10 pm
Location: Derbyshire
My Cars: 1999 Xsara LX 2.0HDI (90) Hatch - Fern
2002 C5 2.0 HDI (110) Estate - Jasmine - SORN
2011 Mini Cooper D Clubman - SOLD
2016 Mercedes A180D Sport - Auto refinement
1992 TZD Turbo - Bluebell - SORN
1992 TZD Turbo Estate - SORN
1991 Gti 16V - Blaze - crash damaged, will get repaired - SORN
1990 Gti 8Valve SOLD - looks like it's been scrapped
2002 Mini Cooper S - SOLD - i miss this car
1992 TXD - Scrapped in March 2014
1988 CX 25 GTI Turbo2 - SORN
1996 - AX Memphis 1.5D - Dream - SORN
x 8

Post by MULLEY »

I never run out of water, i've got one of those huge ibc's with an additional storage unit daisychained upto it, so i just collect free rainwater & have over 1200 litres at my disposal. The ibc only cost me £50 off e-bay. I even share it with my next door neighbours as i can never use enough to run it dry.

On Topic - glad you're getting your car sorted Mat, was it winding the turbo boost up to much that caused the crack in the head? or was it just age?
2002 C5 2.0 HDI Estate - Jasmine - Now SORN
2011 Mini Cooper D Clubman - SOLD
2016 Mercedes A180D Sport - Auto refinement
1992 TZD Turbo - Bluebell - My daily
1991 Gti 16V - Blaze - crash damaged, will get repaired.
1990 Gti 8Valve SOLD - looks like it's been scrapped
2002 Mini Cooper S - SOLD - i miss this car
1992 TXD - Scrapped in March 2014
1988 CX 25 GTI Turbo2 - SORN
1996 - AX Memphis 1.5D - Dream - SORN

I'm not just a username, i'm also called Matthew.
User avatar
mat_fenwick
Moderator
Posts: 7326
Joined: Tue Sep 20, 2005 4:08 pm
Location: North Wales
x 19

Post by mat_fenwick »

Think it was probably a combination of factors really, I had suspected the radiator was not 100% (hence the replacement), and had briefly overheated whilst towing a trailer in the summer. When my Dad had the engine he had badly overheated it previously, which had warped the head - however the garage who repaired it said it wasn't that bad, and didn't bother to skim it. To my mind that would mean extra stresses on the head, but I suppose the turbo didn't help either...have wound it down a touch now! (A shame :( )
Image

1993 1.9 TZD Turbo Estate
1996 3.9 V8 Discovery
1993 VW LT35 campervan
1985 Hyundai Stellar V8
2016 Hyundai iLoad
User avatar
mat_fenwick
Moderator
Posts: 7326
Joined: Tue Sep 20, 2005 4:08 pm
Location: North Wales
x 19

Post by mat_fenwick »

Back on the road now, with hindsight it probably wasn't the cleverest idea to have the first test drive on the way to work this morning - 25 miles, most of it with no mobile coverage...
But all seemed OK, apart from a slipping clutch. Bugger. Must have spilt a bit of diesel in it from the fuel filter, am hoping it will improve and it seems to be. [-o< If not then I'll whip the box out and change it, probably the night before the BXagon just to keep with tradition before a long journey.
The rough running after cold starting, and the smoke doesn't seem to have improve, and I'm now fairly sure the air leak is coming from the fuel pump spindle - I can actually move the spindle in and out a noticeable amount. And if anyone wants to tell me that's a sign of immanent pump death, then just remember I'm trying to subscribe to the 'ignorance is bliss' philosophy... :wink:
Image

1993 1.9 TZD Turbo Estate
1996 3.9 V8 Discovery
1993 VW LT35 campervan
1985 Hyundai Stellar V8
2016 Hyundai iLoad
User avatar
Philip Chidlow
Over 2k
Posts: 11594
Joined: Fri Oct 07, 2005 1:08 pm
Location: Chelmsford, Essex
x 25

Post by Philip Chidlow »

No pressure, Mat, but you CANNOT fail to get it right for the BXagon. :evil: :wink:


OK only kidding. But not much. :lol:
• 1992 Citroen BX TZD Turbo Hurricane
• 2006 Xsara Picasso 1.6 16v
User avatar
Way2go
Over 2k
Posts: 7279
Joined: Fri Jan 13, 2006 3:15 pm
Location: RCoBerkshire
x 2

Post by Way2go »

mat_fenwick wrote: But all seemed OK, apart from a slipping clutch. Bugger. Must have spilt a bit of diesel in it from the fuel filter, am hoping it will improve and it seems to be. [-o<
Just a thought :idea: , would a small dribble of "Fairy Liquid" through the same orifice sort it? Only detergent will disperse the oiliness of oil. Hopefully a small amount won't adversely affect the friction plate or any other bits of the mechanism? :?
1991 BX19GTi Auto
User avatar
mat_fenwick
Moderator
Posts: 7326
Joined: Tue Sep 20, 2005 4:08 pm
Location: North Wales
x 19

Post by mat_fenwick »

Philip Chidlow wrote:No pressure, Mat, but you CANNOT fail to get it right for the BXagon. :evil: :wink:
Relax Phil, it'll be fine! :wink: The rough running/smoke has been exactly the same for the last 20k miles or so (ever since I did the engine swap) and only lasts 30 secods or so. The thing that bugs me the most about it is people who see an oldish car starting smokily and think it's knackered. Far from it IMO.
W2G, that's not a bad idea! My first thought was pouring degreaser in, but I ruled that one out as being too aggressive and beachwear it would probably dry out the release bearing. The clutch has only done 20k miles, so should be plenty of meat left. It's almost stopped now, so think I got away with it...

A far more serious problem however has cropped up today, one which I simply must sort out without delay - the batteries in my Plip key fob have gone flat and I now have to use the key! It is actually a bit of a pain, as the key is a pattern one and not the best fit in the lock. Oh, and I must get an MOT soon as well.
Image

1993 1.9 TZD Turbo Estate
1996 3.9 V8 Discovery
1993 VW LT35 campervan
1985 Hyundai Stellar V8
2016 Hyundai iLoad
User avatar
MULLEY
Over 2k
Posts: 8406
Joined: Thu Jun 22, 2006 11:10 pm
Location: Derbyshire
My Cars: 1999 Xsara LX 2.0HDI (90) Hatch - Fern
2002 C5 2.0 HDI (110) Estate - Jasmine - SORN
2011 Mini Cooper D Clubman - SOLD
2016 Mercedes A180D Sport - Auto refinement
1992 TZD Turbo - Bluebell - SORN
1992 TZD Turbo Estate - SORN
1991 Gti 16V - Blaze - crash damaged, will get repaired - SORN
1990 Gti 8Valve SOLD - looks like it's been scrapped
2002 Mini Cooper S - SOLD - i miss this car
1992 TXD - Scrapped in March 2014
1988 CX 25 GTI Turbo2 - SORN
1996 - AX Memphis 1.5D - Dream - SORN
x 8

Post by MULLEY »

At least batteries are an easy save :lol: I wondered why the clock on my Gti was dead, so had a looksey & previous owner has removed the original clock, glued in the replacement & low & behold its not wired into anything, its battery operated :lol: So a replacement batter is required to fix it.....
2002 C5 2.0 HDI Estate - Jasmine - Now SORN
2011 Mini Cooper D Clubman - SOLD
2016 Mercedes A180D Sport - Auto refinement
1992 TZD Turbo - Bluebell - My daily
1991 Gti 16V - Blaze - crash damaged, will get repaired.
1990 Gti 8Valve SOLD - looks like it's been scrapped
2002 Mini Cooper S - SOLD - i miss this car
1992 TXD - Scrapped in March 2014
1988 CX 25 GTI Turbo2 - SORN
1996 - AX Memphis 1.5D - Dream - SORN

I'm not just a username, i'm also called Matthew.
User avatar
mat_fenwick
Moderator
Posts: 7326
Joined: Tue Sep 20, 2005 4:08 pm
Location: North Wales
x 19

Post by mat_fenwick »

Rear strut now sorted - it would leak hugely through the return pipe ONLY when on high. This turned out to be the rod between the piston and rear arm snapping (something which I have never come across before).
Image
So as the rod had snapped, the piston was moving further outwards then intended, past the first seal, therefore the return pipe was seeing full hydraulic pressure. Fortunately had a spare strut in stock, and I can at least keep the 'old' strut as a spare to match with a decent rod and gaiter.
Image

1993 1.9 TZD Turbo Estate
1996 3.9 V8 Discovery
1993 VW LT35 campervan
1985 Hyundai Stellar V8
2016 Hyundai iLoad
User avatar
mat_fenwick
Moderator
Posts: 7326
Joined: Tue Sep 20, 2005 4:08 pm
Location: North Wales
x 19

Post by mat_fenwick »

mat_fenwick wrote:My first thought was pouring degreaser in, but I ruled that one out as being too aggressive and beachwear it would probably dry out the release bearing.
All I can say is WTF?
I have no idea what word that was supposed to be...the sentence reads fine without it so it must be a reflection on what was on my mind at the time!

Anyway, put new rear pads and discs on, together with a new fitting kit. Most of it was pleasantly unseized, which was nice.
Image
I've also managed to book an MOT for Friday, that's still a whole week to go before the BXagon so hopefully plenty of time if it should fail. Clutch is now no longer slipping, so things are looking up!
Image

1993 1.9 TZD Turbo Estate
1996 3.9 V8 Discovery
1993 VW LT35 campervan
1985 Hyundai Stellar V8
2016 Hyundai iLoad
User avatar
BX Bandit
Backslash Bandit
Posts: 2588
Joined: Thu Aug 31, 2006 7:46 am
Location: Home
My Cars: Cars
x 3

Post by BX Bandit »

Looking good Matt! Do you have front mounted i/c on yours mate?
1990 BX 16V Platinum Grey
1990 BX TGD White
1960 Morris Minor Clarondon Grey
1971 Triumph 2000 Auto Valencia Blue
Post Reply