Clutch for sale - 15,16, 19 petrol, 18,19 diesels

KevR · Post by **KevR** » Wed Oct 12, 2011 5:52 pm

Complete 3-piece clutch kit, brand new. Bought in error - seems to fit everything except a TD, which is what I wanted it for...
Oh, no good for GTi 16V or BX14 either.

£20 collected from Loughborough, or can post at cost (about a tenner I would have thought).

Philip Chidlow · Post by **Philip Chidlow** » Wed Oct 12, 2011 5:55 pm

I think Tim was considering fitting a new clutch to the TZD diesel.

*Update* He was considering... he bought one yesterday!

ken newbold · Post by **ken newbold** » Wed Oct 12, 2011 6:01 pm

I think he's already got one

Mind you, a good investment I would have thought. What make is it?

Post by **Tim Leech** » Wed Oct 12, 2011 6:20 pm

I can collect from Loughborough if that helps, in Keithley tomorrow and Bristol saturday.

KevR · Post by **KevR** » Wed Oct 12, 2011 6:38 pm

As I say, it won't fit a TD anyway, or I'd have kept it!
It's just cluttering up the barn so I'd rather it went to someone who'll use it at some point.

As far as picking up's concerned, trouble is it's not actually in Loughborough yet - will be back there towards the back end of next week.

Not sure what make it is - it was bought in France IIRC but is stamped Made in UK and has a couple of Q-prefix ID marks on it so I'm guessing Quinton Hazel. There's a part number on a sticker on the friction plate but I'd have to go out to the barn to find it!

sdelasal · Post by **sdelasal** » Wed Oct 12, 2011 10:51 pm

will this fit a 1.9D say 89 on?

KevR · Post by **KevR** » Thu Oct 13, 2011 9:43 am

As far as I can tell from the clutch fitment guide I have, it should fit everything as listed above - all carburettor petrol and normally aspirated diesel but not TD and not GTi.
The only thing that might not be right is the release bearing, which has a different reference across the range from the middle of 1989 onwards. I'm pretty sure the two types are interchangeable, but I'll check this afternoon against one I know to be the later type and confirm which sort is with this kit.

KevR · Post by **KevR** » Thu Oct 13, 2011 2:13 pm

sdelasal wrote:will this fit a 1.9D say 89 on?

Yep, it's definitely the later type release bearing so should be fine for your car.

Post by **Tim Leech** » Thu Oct 13, 2011 5:40 pm

KevR wrote:
sdelasal wrote:will this fit a 1.9D say 89 on?
Yep, it's definitely the later type release bearing so should be fine for your car.

Unlike the one I bought

KevR · Post by **KevR** » Thu Oct 13, 2011 6:02 pm

Roverman wrote:
KevR wrote:
sdelasal wrote:will this fit a 1.9D say 89 on?
Yep, it's definitely the later type release bearing so should be fine for your car.
Unlike the one I bought

What's the difference then...? Is it the mounting to the actuator arm? Can't believe the bearing itself is that different, and I'd be surprised if they changed the design of the arm itself.

Mothman · Post by **Mothman** » Thu Oct 13, 2011 7:23 pm

Will it fit an 86 DTR?

Andy

KevR · Post by **KevR** » Fri Oct 14, 2011 4:29 pm

Grenman wrote:Will it fit an 86 DTR?

Andy

I refer the honourable gentleman to my earlier answer:
"As far as I can tell from the clutch fitment guide I have, it should fit everything as listed above - all carburettor petrol and normally aspirated diesel but not TD and not GTi."

However, looks like it's now sold anyway. Thanks to all who expressed an interest.