BX fail

Tell us about life with your BX, or indeed life in general!
Post Reply
Dollywobbler
Over 2k
Posts: 3940
Joined: Sun Dec 04, 2005 2:25 pm
Location: Wales
Contact:

Post by Dollywobbler »

Don't be daunted by the hydraulic system. Just post up your specific problems in the tech section and it's amazing how it begins to make sense after a while! Height correctors can and should be lubricated I believe, but I've never done it myself. Something else to learn...

I wonder if a non-return valve in your fuel line would help with the carb drain issue?
User avatar
MULLEY
Over 2k
Posts: 8406
Joined: Thu Jun 22, 2006 11:10 pm
Location: Derbyshire
My Cars: 1999 Xsara LX 2.0HDI (90) Hatch - Fern
2002 C5 2.0 HDI (110) Estate - Jasmine - SORN
2011 Mini Cooper D Clubman - SOLD
2016 Mercedes A180D Sport - Auto refinement
1992 TZD Turbo - Bluebell - SORN
1992 TZD Turbo Estate - SORN
1991 Gti 16V - Blaze - crash damaged, will get repaired - SORN
1990 Gti 8Valve SOLD - looks like it's been scrapped
2002 Mini Cooper S - SOLD - i miss this car
1992 TXD - Scrapped in March 2014
1988 CX 25 GTI Turbo2 - SORN
1996 - AX Memphis 1.5D - Dream - SORN
x 8

Post by MULLEY »

Very rare for a height corrector to actually fail, the internal bits can be changed as there are kits out there i believe, but its most likely the linkages which are a bit seized, get some WD40 on them to free them up & do some citreobics to help it along, then get some grease onto them for better lubrication than wd40.

Have you tried lubricating the front struts yet as per the DIY section? Don't forget you can also add some 3in1 oil or similar into the tops of the struts where the rubber bungs are below where the spheres are mounted. One side won't have a bung in it, so just pop a couple of drops in & then do some citreaobics, hopefully that'll help.
2002 C5 2.0 HDI Estate - Jasmine - Now SORN
2011 Mini Cooper D Clubman - SOLD
2016 Mercedes A180D Sport - Auto refinement
1992 TZD Turbo - Bluebell - My daily
1991 Gti 16V - Blaze - crash damaged, will get repaired.
1990 Gti 8Valve SOLD - looks like it's been scrapped
2002 Mini Cooper S - SOLD - i miss this car
1992 TXD - Scrapped in March 2014
1988 CX 25 GTI Turbo2 - SORN
1996 - AX Memphis 1.5D - Dream - SORN

I'm not just a username, i'm also called Matthew.
User avatar
Willy
BXpert
Posts: 474
Joined: Sat Aug 06, 2011 9:17 pm
Location: Reading

Post by Willy »

Thanks for the tips, I'll try lubing the struts re this thread and greasing the height corrector linkage, not so sure abut the latter though as the internet will only tell me about Xantia stuff there.

Eugh fuel starvation has become so irritating now. Even after just one night of standing the routine is: five seconds on the facet pump, then three or four cycles of a few right-pedal pumps and cranking. Even after the engine finally catches it might die a few seconds later. Booo.

In other bad news the brakes are starting to feel weirdly ineffective (unless I've just forgotten how much force needs applying on the pedal) and much worse than all this mechanical nonsense, the red on the tailblazer is starting to fade :cry:
ImageImageImageImageImage
User avatar
MULLEY
Over 2k
Posts: 8406
Joined: Thu Jun 22, 2006 11:10 pm
Location: Derbyshire
My Cars: 1999 Xsara LX 2.0HDI (90) Hatch - Fern
2002 C5 2.0 HDI (110) Estate - Jasmine - SORN
2011 Mini Cooper D Clubman - SOLD
2016 Mercedes A180D Sport - Auto refinement
1992 TZD Turbo - Bluebell - SORN
1992 TZD Turbo Estate - SORN
1991 Gti 16V - Blaze - crash damaged, will get repaired - SORN
1990 Gti 8Valve SOLD - looks like it's been scrapped
2002 Mini Cooper S - SOLD - i miss this car
1992 TXD - Scrapped in March 2014
1988 CX 25 GTI Turbo2 - SORN
1996 - AX Memphis 1.5D - Dream - SORN
x 8

Post by MULLEY »

Is there much left on the pads, if they are low then that might account for them seemingly to feel a bit soft? Or, is your lhm old?
2002 C5 2.0 HDI Estate - Jasmine - Now SORN
2011 Mini Cooper D Clubman - SOLD
2016 Mercedes A180D Sport - Auto refinement
1992 TZD Turbo - Bluebell - My daily
1991 Gti 16V - Blaze - crash damaged, will get repaired.
1990 Gti 8Valve SOLD - looks like it's been scrapped
2002 Mini Cooper S - SOLD - i miss this car
1992 TXD - Scrapped in March 2014
1988 CX 25 GTI Turbo2 - SORN
1996 - AX Memphis 1.5D - Dream - SORN

I'm not just a username, i'm also called Matthew.
Defender110
Over 2k
Posts: 5917
Joined: Wed Dec 16, 2009 8:02 pm
Location: Harwood, Bolton
My Cars: Land Rover Discovery Series 1 200tdi 3 door
Land Rover Discovery Series 2 Facelift TD5
2020 Fiat Panda cross 4x4 twin air.
x 27

Post by Defender110 »

Could this now be a fuel evaperation problem, is the engine running hot, has it got an insulation gasket between the carb and manifold, is the carb still bolted down securely?
Kevan
1997 Mercedes C230 W202
2003 Land Rover Discovery Series 2 Facelift TD5 - Daily driver / hobby days and camping.
1993 Land Rover Discovery 200tdi Series 1 3 door - in need of TLC
2020 Fiat Panda 4x4 Cross Twin Air.
User avatar
Willy
BXpert
Posts: 474
Joined: Sat Aug 06, 2011 9:17 pm
Location: Reading

Post by Willy »

MULLEY wrote:Is there much left on the pads, if they are low then that might account for them seemingly to feel a bit soft? Or, is your lhm old?
Bob never professed to have changed the LHM himself, so its been about 2 years/10k miles without changing. But the power steering does feel a shade heavy too, so this may well be the root of all my problems :oops:

Also, first squeal this morning! Engine turned and heard a little squeally belt for the first time for a couple of seconds.

And yes Kevan, I believe it is evaporation as the car does seem to smell alot of petrol around the bonnet when it's been parked up, and google agrees with me. Something else to investigate later.
ImageImageImageImageImage
User avatar
Willy
BXpert
Posts: 474
Joined: Sat Aug 06, 2011 9:17 pm
Location: Reading

Post by Willy »

Onto the operating table...

Image

Working in a concoction of piss, vomitus and dead rats... lovely

Image

Tried lubing linkage:

Image
Image

And my poor snap on the HC itself

Image

Well, it made no difference. Operating the linkage from the lever still feels quite stiff, and after one low to highest cycle the front steadfast refused to budge. I couldn't therefore lube the struts either as they were somewhat innaccessable and incitaerobatical. So I'm now parked up like this until it sinks back down at the rear and (fingers crossed) rises up to normal as per that "first start" of the day:

Image

Looks like it'll be a somewhat expensive trip to the garage before long...
ImageImageImageImageImage
Gary
BXpert
Posts: 259
Joined: Thu Jul 17, 2008 5:16 pm
Location: bedfordshire
x 3

Post by Gary »

Did you lubricate the bush on the sub frame that the height corrector linkage pivots on?
It is a bit difficult to see from underneath but i think you can see it on the o/s from under the bonnet on the petrol models behind the engine near the steering rack.
It is number 4 in this diagram
Image
User avatar
Willy
BXpert
Posts: 474
Joined: Sat Aug 06, 2011 9:17 pm
Location: Reading

Post by Willy »

Thanks for the image Gary - I can see what you're pointing at although I couldn't quite get lube that far in, it was fairly inaccessible. Haven't had any new rising problems though, goes up to normal fine, but still requiring some playing with the adjuster lever.

My HP belt isn't as tight as it could be though, if this would affect anything?

In other news... Picked up the new Speedlines from Dean yesterday, what a nice fellow, threw in his cat too :wink:, or rather it threw itself in...

Image
Image

Wheels were a bit grubby, but a bit of brillo pad has got the worst of the muck off, and then some rain helped clean off the copious amounts of brake dust I released, mm lung cancer! Hopefully some chemical wheel cleaner will get rid of the small stain patches and then they'll be all good in that hood.

Now, to investigate my rapidly deteriorating fuel consumption...
ImageImageImageImageImage
User avatar
djoptix
BXpert
Posts: 891
Joined: Fri Oct 28, 2005 12:48 pm
Location: Bristolcestershire
x 2

Post by djoptix »

I sold those to Dean back in the day. They came from a chap called Tom on the old old BX16v forum. I paid him £100 and stripped a load of stuff off a 16v down Essex way.

They were very badly curbed so I restored them with a wire wheel on my drill :)
Good heavens! My signature's been moderated...
User avatar
Willy
BXpert
Posts: 474
Joined: Sat Aug 06, 2011 9:17 pm
Location: Reading

Post by Willy »

Don't cars look lovely under a uniform layer of frost

Image
ImageImageImageImageImage
User avatar
Mike E (uk)
1K Away
Posts: 1115
Joined: Sun Aug 14, 2005 9:10 am
Location: High Wycombe, Bucks
x 1

Post by Mike E (uk) »

I recommend you get an immersible pump to clear the water from the pit.

you don't want to drop your tools in there!

Mike
la BX 16 soupapes: sachez apprecier avec moderation.



It might be clever now, but it won't be in the morning!
User avatar
Willy
BXpert
Posts: 474
Joined: Sat Aug 06, 2011 9:17 pm
Location: Reading

Post by Willy »

We have one of those actually as our cellar doesn't take kindly to the local river flooding.

In the nearby Vauxhall garage on my way home earlier, spot the mistake and win a big prize:

Image
ImageImageImageImageImage
User avatar
Tim Leech
Over 2k
Posts: 15565
Joined: Tue Apr 15, 2008 11:12 am
Location: Derbyshire
My Cars: Various
x 141

Post by Tim Leech »

Willy wrote:In the nearby Vauxhall garage on my way home earlier, spot the mistake and win a big prize:

Image
Well they do work for Vauxhalll.................. :wink:
Lots of Motors, mostly semi broken....
User avatar
Willy
BXpert
Posts: 474
Joined: Sat Aug 06, 2011 9:17 pm
Location: Reading

Post by Willy »

Squeeeaaaky squeaky HP belt this morning.. :?
ImageImageImageImageImage
Post Reply