DUFF ABS
by tim leech » Mon Apr 09, 2007 4:20 pm
First post
Mine doesnt work although I have replaced the non ABS driveshaft with a correct one (thanks Ian), the ABS light went out once for about 2 seconds a...
Last post
Thanks matey, cars in tomorrow having the welding done and the other driveshaft fitted, will have a looky while its up on the ramps to see if theres...
10 Replies
905 Views
Last post by tim leech Tue Apr 10, 2007 7:16 pm
Parts removal, ideas please...
by cavmad » Mon Apr 09, 2007 12:32 pm
First post
...hi will be trying to remove the last few salvegable parts from the TZD hatch this afters. Can someone please explain in layman`s terms how to...
Last post
If you're in a position to pipe-clip, then the rear arms can come off pretty easily if you have a 24mm ring spanner, a 24mm socket and a breaker bar....
13 Replies
1055 Views
Last post by DLM Tue Apr 10, 2007 1:45 pm
Stalling solved?
by toddao » Sun Apr 08, 2007 3:30 pm
First post
I've been trying to cure the uphill stalling issues that have afflicted the old diesel.
Last post
My old GTI/TD used to fill up the filter with water, never did find out where it came from, I used to use various productscalled pump saver, or dry...
1 Replies
354 Views
Last post by Stewart (oily!) Sun Apr 08, 2007 7:45 pm
A long term air/con fault fixed
by AlanS » Fri Mar 23, 2007 8:41 am
First post
Here's a posting I made on another forum. Long winded admittedly, but has some info that might save someone the frustrations I've had in recent years...
Last post
Hi Alan,
8 Replies
866 Views
Last post by m_2975 Sun Apr 08, 2007 11:44 am
Price of a cam belt / cam belt kit ?
by soxer123 » Wed Apr 04, 2007 3:56 pm
First post
I am wondering what sort of price I should be paying for a cam belt / cam belt kit for my 1990 1.6 BX meteor (hope that is enough info) ?
Last post
i've just got a Quinton Hazell timing belt for my TZD, are they ok?
7 Replies
799 Views
Last post by docchevron Sun Apr 08, 2007 1:09 am
Blip Unlock. Blip… nothing. Eh?
by BackinaBX » Mon Apr 02, 2007 6:30 pm
First post
Hello chaps.
Last post
I suppose it could also could beworth trying what I endlessly end up doing with TV remotes: taking the batteries out and then putting them back in...
9 Replies
1064 Views
Last post by DLM Sat Apr 07, 2007 6:33 pm
BX / ZX / Peugeot 1580cc cylinder head
by mnde » Wed Mar 28, 2007 2:44 pm
First post
What differences are there (apart from the obvious hydraulic ones) between the BX and ZX 1.6 XU/B2C engine?
Last post
Yep, the eBay Meteor is my daily driver while the GSA is having its cabin water leaks sorted @ Chevronics following its MOT, which it sailed straight...
9 Replies
783 Views
Last post by stuart_hedges Fri Apr 06, 2007 8:31 pm
More aircon issues
by Jaba » Thu Apr 05, 2007 6:17 pm
First post
I have posted about this problem before but it remains unresolved. The car has been laid up for a while but I plan to use it again this summer.
Last post
That sounds like sensible advice Alan. The d/r is original - 17 years old now with no sight glass.
2 Replies
442 Views
Last post by Jaba Fri Apr 06, 2007 10:29 am
For anyone with a non working air/con.
by AlanS » Wed Apr 04, 2007 12:42 am
First post
I've posted this on another forum, but seeing as you guys are heading into the hotter weather, thought it might be of interest to you also....
Last post
Yep, I've got the little buttons by the handbrake! Which I quite like! Bugger all idea how to wire them in, but they look pretty, and I like...
10 Replies
823 Views
Last post by docchevron Fri Apr 06, 2007 2:27 am
vibration?
by simonbx17 » Wed Apr 04, 2007 9:47 pm
First post
i wounder if any can help my bx seems to vibrate like some has got of my steering wheel and is shaking it from side to side at about 70mph onwards...
Last post
thanks for your advice i will do the relivent checks it's more than likely a combination of things drop links, driveshafts as my bx makes that sort...
8 Replies
643 Views
Last post by simonbx17 Thu Apr 05, 2007 9:43 pm
1.6 TRS Oil in one of the bores
by Jezzie 16v » Sat Mar 24, 2007 1:57 pm
First post
Been having a bit of trouble with it for a few weeks now, it has been using (not losing) a bit of water but with no real signs of H/G failure but...
Last post
The Haynes reckons worn rings,bores or valve guides is likely, has anyone else come across this with the 1.6 ?
16 Replies
1577 Views
Last post by DLM Thu Apr 05, 2007 6:41 pm
Seat recline mechanism failure?
by paulwitchard » Tue Mar 27, 2007 6:54 pm
First post
Have just got new to me BX TZD estate home - see the day I went to Nyland etc on BX chat thread - but seat recline mechanism on both front seats...
Last post
I've taken apart a number of BX seats in my time: the recline mechanism is actuated, as all have said, by a knurled plastic dial to one side of the...
11 Replies
949 Views
Last post by DLM Thu Apr 05, 2007 1:17 pm
O/S front window required
by ianselva » Tue Apr 03, 2007 6:27 pm
First post
Hi, The drivers window on my TZD can not be wound down as the runner on the bottom has rusted and split. Is it possible to get just the runner or...
Last post
Musat have been me that put it badly matey! I knew exactley what you meant!!
3 Replies
575 Views
Last post by docchevron Thu Apr 05, 2007 2:43 am
Where's the engine no on my TZD
by paulwitchard » Wed Apr 04, 2007 7:53 am
First post
I hope this does not sound too helpless but I cannot find the engine number on my TZD - I need it to complete an export certificate for the DVLA, and...
Last post
The engine number is on the right hand side of the block on a little riveted on plate it is not a huge number i think it is about 5 numbers long also...
2 Replies
418 Views
Last post by sleepy0905 Wed Apr 04, 2007 9:30 am
Exhaust question...
by cavmad » Sun Apr 01, 2007 11:03 pm
First post
..excuse me if this sounds a strange question but it is a genuine one. Can someone please tell m the exact length of a TZD estate backbox from where...
Last post
Count yourself lucky Billy, I had a VERY narrow escape a while back. That would have really bu&&ered up the time I get to spend on cars and...
13 Replies
1021 Views
Last post by docchevron Wed Apr 04, 2007 2:37 am
Sticking handbrake
by classic2cv » Tue Apr 03, 2007 4:15 pm
First post
I’ve got my car through the Mot and back on the road after a bit f a lay up :D
Last post
you might just have a point there
2 Replies
383 Views
Last post by classic2cv Tue Apr 03, 2007 5:37 pm
Hand brake adjustment
by classic2cv » Fri Mar 30, 2007 11:49 am
First post
when I try to adjust the handbrake it does not last long
Last post
the cables are showing their age but are still moving ok
6 Replies
688 Views
Last post by classic2cv Tue Apr 03, 2007 4:46 pm
MOT failure on Sticky Caliper and Handbrake
by moremeba » Thu Mar 29, 2007 5:05 pm
First post
All, can anyone advise on how to cure the above....the mot man said that my front passenger side caliper is sticking and my handbrake has too much...
Last post
I had enormous trouble screwing one piston in last time I changed the pads. Loosening off the bleed bolt cured that. If you do loosen it, use a...
4 Replies
1126 Views
Last post by Oscar Tue Apr 03, 2007 10:04 am
Quelle couleur ?
by Doz » Wed Mar 28, 2007 7:49 pm
First post
Ok...
Last post
it should be silver birch metalic same as our old tgs meteor
4 Replies
556 Views
Last post by rob-bx16v Mon Apr 02, 2007 10:36 pm
Advice needed: Is it worth it?
by DavidRutherford » Sat Mar 31, 2007 9:00 pm
First post
Year-and-a-bit ago, I picked up a BX TZD for my sis. Cambelt, Water pump, LHM change, Rear arm bearing, MOT and it was a goodun.
Last post
There is always more rust than you think... and the back end of a BX hatch nearly always rusts out. The only hatch I've had where this didn't hold...
21 Replies
1903 Views
Last post by DLM Mon Apr 02, 2007 1:32 pm
Undesired fluid issue changing strut - am I shafted?
by AdrianO » Sat Mar 31, 2007 4:25 pm
First post
I was happily changing a n/s suspension strut - about the limit of my expertise, but something I've now done several times - and got so engrossed...
Last post
See regarding oil type and location of filler plug.
3 Replies
591 Views
Last post by ellevie Sat Mar 31, 2007 7:07 pm
ignition switch?
by Andy G » Tue Mar 27, 2007 8:13 pm
First post
how hard is it to replace an ignition switch?
Last post
Excellent!
16 Replies
1858 Views
Last post by Philip Chidlow Fri Mar 30, 2007 10:10 pm
I'm on my belly... and can't get up!
by BackinaBX » Thu Mar 29, 2007 10:27 pm
First post
Hello chaps, long time no see!
Last post
It worked! There's just me on this one, so it was a bit of a trial and error thing... but she's back up on her feet and running smooth. Took her out...
4 Replies
702 Views
Last post by BackinaBX Fri Mar 30, 2007 5:49 pm
Where do they go
by artic-steel » Mon Mar 26, 2007 11:35 pm
First post
I have a 16TGS, the return pipe between the acumulator sphere & reservoir has split.
Last post
Andy, I have various lengths of old octopus/lhm pipe from a couple of BX`s I`ve scrapped. If you can make use of any of them please let me know and...
11 Replies
1023 Views
Last post by cavmad Fri Mar 30, 2007 12:57 pm
Petrol Leak
by kiwi » Thu Mar 15, 2007 5:01 am
First post
My BX has sprung a leak, petrol was pouring out from over the fuel tank. Went hunting for the only drain point I knew where the sender goes in to...
Last post
Finally got it fixed today after locating a second hand Sender unit, yesterday took a gamble and filled with 40 litres from the yellow warning light...
4 Replies
930 Views
Last post by kiwi Fri Mar 30, 2007 11:44 am
17" alloy wheel pressures
by simonbx17 » Thu Mar 29, 2007 10:50 pm
hi,
0 Replies
284 Views
Last post by simonbx17 Thu Mar 29, 2007 10:50 pm
So, 7 seat conversion into BX estate. Anyone done one?
by cavmad » Sun Mar 25, 2007 2:40 pm
First post
Have seen a 7 seat BX estate for sale a long while back, obviously a conversion, and I recall someone from here posting a link to the company that...
Last post
NOOOOO! While the risk of electrocution is very low, you might trip the eject mechanism by mistake and you have not got a sunroof! (yet!)
20 Replies
1425 Views
Last post by tom Thu Mar 29, 2007 7:56 pm
Pipes
by Philip Chidlow » Thu Mar 29, 2007 10:10 am
First post
I have a question (or two). When did plastic coated pipes come in? (my understanding is 1990 with the - confusingly - 1991 model range, which also...
Last post
By far the easiest solution is to bin the steel pipes (coated or not) and replace them with kunifer using stainless unions. Job done. FOREVER.
4 Replies
428 Views
Last post by Kitch Thu Mar 29, 2007 7:22 pm
Regenerating metallic paintwork
by Philip Chidlow » Thu Mar 29, 2007 1:30 pm
First post
As the heading suggests, what is the best thing to do to bring metallic (silver) paintwork back to it's bright best? My estate's roof in particular....
Last post
T-Cut's a good place to start, or failing that get it mopped.
5 Replies
529 Views
Last post by Kitch Thu Mar 29, 2007 7:21 pm
2nd new starter motor in 6 months
by cacaolat » Mon Mar 26, 2007 9:39 pm
First post
got the car to the garage today....will get more details tomorrow, but the starter motor, which was fitted new last October is gone. Even the one,...
Last post
I had a Cavalier many years ago that used to do this. Starter would stick on every now and then. Eventually I carried a small chunk of steel with me...
4 Replies
525 Views
Last post by DavidRutherford Thu Mar 29, 2007 11:12 am
Cavmad does technical! Auto box problem solved!
by cavmad » Wed Mar 28, 2007 3:39 pm
First post
With thanks for the info on parts numbers etc I`ve sorted the niggly fault on the autobox cable.
Last post
Theres hope for me then!
9 Replies
652 Views
Last post by tim leech Thu Mar 29, 2007 9:46 am
Locking problems of an electical nature?
by AlanS » Thu Mar 22, 2007 9:44 pm
First post
This one should have your thinking caps working overtime.
Last post
First place I went when the car began to play up. Clean as a whistle and I always refit with the added security of a large zip tie after I had one go...
8 Replies
696 Views
Last post by AlanS Wed Mar 28, 2007 9:09 pm
Veg Oil Pre Heater
by Bluey1978 » Wed Mar 28, 2007 8:06 pm
Hi
0 Replies
310 Views
Last post by Bluey1978 Wed Mar 28, 2007 8:06 pm
Interior lights don't come on when the doors are open...
by simonineaston » Mon Mar 26, 2007 12:24 pm
First post
Hi Folk, I've got the bit between me teeth good and proper after doing the heater fan pcb mod. :-) This week's problem is to do with my courtesy...
Last post
I'll try your various advice re: the pix later today... Cheers !
10 Replies
858 Views
Last post by simonineaston Wed Mar 28, 2007 1:48 pm
BX restoration project
by jrdpod » Mon Mar 26, 2007 8:43 pm
First post
Hi all,
Last post
I thought those 17 n/a's were the rarest BX? except the 4x4's of course.
3 Replies
512 Views
Last post by MULLEY Tue Mar 27, 2007 11:38 pm
Manual Gearbox Oil Replacement WARNING (Reverse Gear Clamp)
by ellevie » Mon Mar 26, 2007 12:15 pm
First post
If you follow the Haynes manual instructions, there is a chance that you will confuse the reverse gear shaft 13mm clamp bolt with one of the drain...
Last post
Vanny learnt the lesson about that bolt the hard way ISTR..... :(
4 Replies
787 Views
Last post by RichardW Tue Mar 27, 2007 12:27 pm
Rear wash/wipe
by stuart_hedges » Mon Mar 26, 2007 3:50 pm
First post
One of the very few problems with my newly-acquired BX is that the rear wash/wipe doesn't work.
Last post
And in mine, the motor is burnt out because the whole thing is siezed solid.
2 Replies
380 Views
Last post by tom Mon Mar 26, 2007 8:10 pm
Fitting an Aerial
by Philip Chidlow » Fri Mar 23, 2007 2:07 pm
First post
Hi I have a replacement aerial for my BX 16TGS and although it looks simple enough, I thought I'd ask if anyone has any tips for safely removing the...
Last post
You may find some second hand cassettes in charity shops - otherwise I think Maplins and others sell adaptors for later things to use it.
5 Replies
470 Views
Last post by jeremy Mon Mar 26, 2007 2:09 pm
Gearbox or clutch prob and is it terminal?
by Numptychucker » Mon Mar 26, 2007 1:11 am
First post
Hopefully you guys may be able to help at least diagnose this prob
Last post
Save yourself some grief
8 Replies
604 Views
Last post by ellevie Mon Mar 26, 2007 12:18 pm
BX renovation - help and space needed
by Oscar » Fri Mar 23, 2007 11:40 am
First post
Hi
Last post
I've got space/time on weekend of 28th April if that is OK for all.
11 Replies
906 Views
Last post by jonkw Mon Mar 26, 2007 10:54 am
TGS tyre specs: Manual vs Auto
by Philip Chidlow » Tue Mar 20, 2007 11:17 am
First post
I have a question: Why, in the original specification were 165/70 R14s OK for the manual 16TGS but the automatic version is listed as being shod with...
Last post
Philip, yes I finally looked at the tyres of my car yes the are 175/70 R14 Michelin Energy's
14 Replies
1342 Views
Last post by cacaolat Sat Mar 24, 2007 7:46 pm
Tightening handbrake
by Eric Brough » Sun Mar 11, 2007 6:06 pm
First post
I've just acquired a BX19D Estate. All in reasonable shape, with new front pads and discs. However, the handbrake pulls up almost to the limit of its...
Last post
Further investigation revealed that the lever on one caliper was sticking intermittently. It was not returning freely to the 'handbrake off...
5 Replies
694 Views
Last post by Eric Brough Sat Mar 24, 2007 2:20 pm
more starting trouble.....with BX 16 TGS UPDATED
by cacaolat » Fri Mar 23, 2007 6:20 pm
First post
In recent months I had 3 times trouble starting the car after stalling it. This was always on a cold day. After that I had another problem which...
Last post
:(
7 Replies
733 Views
Last post by cacaolat Sat Mar 24, 2007 12:10 pm
where to buy new battery terminals
by cacaolat » Tue Mar 20, 2007 8:08 pm
First post
because of the trouble ...see below Meteor 16 TGS starting issues I will buy some new battery terminals. Any advice on a good place to buy them, and...
Last post
Anyone got a solex manual choke kit? *or even a place to buy one?
9 Replies
1012 Views
Last post by ellevie Fri Mar 23, 2007 9:00 pm
Tools
by tom » Wed Mar 21, 2007 8:09 pm
First post
Somebody on Ebay is flogging a job lot of Citroen tools including some for the BX. I have placed a substantial bid in for these items which will, if...
Last post
Well spotted! I'll have to join the club. (Do any of them fit cam belts for you? ;-) )
2 Replies
424 Views
Last post by simonineaston Fri Mar 23, 2007 12:24 pm
How do I get the heater dial panel off!?
by simonineaston » Tue Mar 20, 2007 1:02 pm
First post
Confession-time here, folks - I've read another thread on this forum explaing how to get this panel off, but I didn't get it! I've got as far as A)...
Last post
A picture tells a thousand words :) I'll put it in a new thread if the moderators wish to make it sticky
16 Replies
1574 Views
Last post by Doz Thu Mar 22, 2007 8:59 pm
Sunroof corrosion...
by Doz » Wed Mar 21, 2007 8:52 pm
First post
OK, it's rusted through .... does anyone have a good spare or advise for changing it??
Last post
I'll se if my mate Ben is down your neck of the woods... if he is , I'll PM you and make the arrangements.
8 Replies
923 Views
Last post by Doz Thu Mar 22, 2007 5:56 pm
Will ZX alloys fit BX's?
by MULLEY » Mon Mar 19, 2007 10:09 pm
First post
The rim size is quoted as 14inch 5.5J 4-24 offset.
Last post
I was going to bid on some, but the dingbats never replied to my queries, & now its ended?? i dont know why some people bother listing stuff...
8 Replies
864 Views
Last post by MULLEY Wed Mar 21, 2007 11:16 pm
Progress on 17RD D526 WCW
by jrdpod » Mon Mar 19, 2007 8:54 pm
First post
Some of you will have been following my exploits on this car.
Last post
Oh yeah, rogue scrappers....I hadn't thought of that.
11 Replies
1044 Views
Last post by Kitch Wed Mar 21, 2007 7:09 pm
Speedo cable BX 16v
by pinfold » Mon Mar 19, 2007 9:48 am
First post
I am now on my second new speedo cable in 6 months,
Last post
I always go armed with part numbers. Without the part number they ask for my vehicle registration number and then promptly decide that my 19TRS...
6 Replies
714 Views
Last post by ellevie Wed Mar 21, 2007 8:28 am
Forum permissions
You cannot post new topics in this forumcannot reply to topics in this forumcannot edit your posts in this forumcannot delete your posts in this forumcannot post attachments in this forum
