Tracking
by toddao » Thu Oct 13, 2011 11:38 am
First post
I had my tracking adjusted a few weeks back but the mechanic wasn't too clued up about hydraulic Citroens. He did the adjustment in the second...
Last post
They fit the metal clamps over the rear wheels while the car is in high position then they do actually fit under the rear arches when it goes lower....
5 Replies
552 Views
Last post by toddao Sat Oct 15, 2011 10:54 pm
leaking sunroof.
by ace_the_bass » Thu Oct 13, 2011 12:49 pm
First post
has anyone experienced much of this? after a week of bad weather up here i started the car on tuesday afternoon and as the suspension lifted up at...
Last post
To clear my drain hole, I had to remove the entire head lining and sun roof assembly.
13 Replies
592 Views
Last post by Mike E (uk) Fri Oct 14, 2011 10:32 pm
Tailgate doesn't lock
by robt » Wed Oct 12, 2011 11:02 pm
First post
I'm slowly working my way through the jobs on my BX, but this one has me stumped. Despite doing many adjustments and general faffing about getting...
Last post
That's a general fault with most BX estates, due to the weight of the tailgate; these are incredibly heavy. It really used to annoy me when people...
5 Replies
334 Views
Last post by robt Thu Oct 13, 2011 10:46 am
Ivor the Engine noises..
by DomRobinson » Wed Oct 12, 2011 3:18 pm
First post
Whilst stationary, or just taking off from traffic lights, for example, the hydraulic system on my TZD has started making steam engine noises which...
Last post
pm. sent
3 Replies
309 Views
Last post by citronut Thu Oct 13, 2011 9:11 am
Replacement of water temp sensor. 1.9 d
by pmh » Wed Oct 12, 2011 3:35 pm
First post
I had assumed that I could directly replace one of the temp sensor switches on the thermostat housing with an aftermarket analogue sensor and temp...
Last post
I had this problem with the sensor that I fitted too. I took one of the original sensors out of the thermostat and used a tap to cut the smaller...
4 Replies
260 Views
Last post by toddao Thu Oct 13, 2011 7:35 am
Coolant change on a 1.9 n/a diesel
by robt » Tue Oct 04, 2011 12:26 pm
First post
Does anyone have any tips or advice on how to successfully change the coolant on a 1.9 diesel? Are the systems prone to air locks? The lack of temp...
Last post
if you can get hold of the block with the screw going through it with a pair of vice grips, you will be able to break it away/off if you carefull,...
15 Replies
898 Views
Last post by citronut Tue Oct 11, 2011 1:20 pm
Diesel sump plug washer
by robt » Sat Oct 08, 2011 12:06 am
First post
Simple question - what type of washer do I need before doing an oil change? Is it this aluminium/rubber type:
Last post
I just pop down to the Citroën dealer. Buy a load at once always get a good discount.
8 Replies
438 Views
Last post by robt Mon Oct 10, 2011 3:48 pm
GT MK1 (carb) fuel pump
by B-Hive » Fri Sep 16, 2011 5:43 am
First post
Just did an awesome coast circuit.. Canberra---coast---Sutherland---Canberra in the BX GT ...such a great animal on the open road...however I do...
Last post
the second choke butterfly is mechanicaly opend by a cam on the thtrotle linkage, but cant open till the choke mechanisum if fully off, as it is...
14 Replies
537 Views
Last post by citronut Sun Oct 09, 2011 9:44 pm
Wiper Problem
by kiwi » Sun Oct 09, 2011 5:53 am
The latest addition has a problem where the intermittant wipe and wipe during the washer function does not work.
0 Replies
235 Views
Last post by kiwi Sun Oct 09, 2011 5:53 am
Sticky struts - where do I put the lube eh?
by Wooscary » Wed Sep 28, 2011 1:07 pm
First post
I know this has been asked many times before, and I've searched for
Last post
Pull the end of rubber pipe from their fixing and plonk the open end into a cup/jar of LHM. Then put your suspension on high and as the car rises...
10 Replies
1810 Views
Last post by Way2go Sat Oct 08, 2011 5:46 pm
Citroen DS ignition lock barrel
by Dennis Rosser » Sat Oct 08, 2011 9:18 am
First post
Hi, not strictly BX I know but you've never let me down before, so, does anyone know how to remove the ignition lock barrel ? I have almost...
Last post
Glad you got it out Dennis,
3 Replies
319 Views
Last post by Mothman Sat Oct 08, 2011 5:12 pm
Engine won't stop
by TB2 » Tue Sep 27, 2011 11:35 am
First post
Hi there,
Last post
I'll see if we have one in stock when I'm back at work if you like?
10 Replies
977 Views
Last post by TB2 Thu Oct 06, 2011 11:58 pm
Rear height correct
by ace_the_bass » Thu Oct 06, 2011 8:12 pm
First post
Does anyone know what the availability of these things are? Having a job getting hold of one. Also how big a job is it to fit?
Last post
hi malcom. im wanting to change it as it is leaking and the mot tester failed it today.
3 Replies
302 Views
Last post by ace_the_bass Thu Oct 06, 2011 10:41 pm
Diesel fuel pipe sizes - the metal ones.
by paulwitchard » Thu Oct 06, 2011 7:03 pm
First post
Had a poke around under the non turbo diesel this pm courtesy of KevR's ramp, and it seems that the metal pipe to and from the diesel tank are...
Last post
not sure of the inner diamiter but they are quite thin walled if that helps,
1 Replies
170 Views
Last post by citronut Thu Oct 06, 2011 10:17 pm
Cold start advance
by Wooscary » Mon Sep 26, 2011 1:15 pm
First post
So, after seeing pictures of other people's cold start advance mechs, I realised that mine is missing the wire/cable that comes out of the end of it....
Last post
Cheers for the picture. I can't quite see where the cable goes, but there are only so many options I suppose.
7 Replies
428 Views
Last post by Wooscary Thu Oct 06, 2011 9:06 pm
Tyre recommendations
by Jmcc » Mon Oct 03, 2011 7:41 pm
First post
As the topic says - any recommendations for tyres for my TZD?
Last post
Aye. My A-series fleet is on Toyos as well. Very impressed.
18 Replies
794 Views
Last post by Dollywobbler Wed Oct 05, 2011 3:50 pm
Choice of engine oil
by anaconda » Tue Oct 04, 2011 10:46 am
First post
Next job will be an oil change. Does anyone have a specific brand/spec of engine oil they would recommend for a diesel.
Last post
I use semi snyth in all my motors, its VW own brand which I get for £12 for 5 litres.
2 Replies
216 Views
Last post by Tim Leech Tue Oct 04, 2011 11:22 am
Abs sensors
by Jmcc » Sun Oct 02, 2011 9:12 am
First post
I have an intermittent ABS light issue. PO warned me and said it was one of thd front sensors. He has a new, genuine Citroen sensor he'll sell me but...
Last post
Perfect sense! Thanks.
5 Replies
369 Views
Last post by Jmcc Mon Oct 03, 2011 11:12 am
Fuel heater / water hose needed
by YorkieG » Sat Oct 01, 2011 4:49 pm
First post
Hi to all members, could anyone help me find/obtain the correct hose details for the hose that connects to the diesel fuel heater and the fixed metal...
Last post
DIN 73411 says they're good! :D
9 Replies
709 Views
Last post by Way2go Mon Oct 03, 2011 5:07 am
Fuel gauge and handbrake
by Dollywobbler » Fri Sep 30, 2011 5:15 pm
First post
Two seemingly unlinked issues, but they both involve a dashboard, so I've bunged them into one thread.
Last post
You can always replace the handbrake swith with the bootlight switch :wink:
14 Replies
597 Views
Last post by kiwi Sun Oct 02, 2011 7:26 pm
1.9 n/a powerhouse
by Philip Chidlow » Mon Sep 26, 2011 10:34 pm
First post
Well, perhaps not, but (because I don't want to bother Kermit with my ignorance while he's so tied up getting his glorious workshop up and running) I...
Last post
given we will be carrying kit and tools with us too. So making sure it's working as well as is reasonable to expect and losing some weight...
26 Replies
1071 Views
Last post by docchevron Sun Oct 02, 2011 2:17 am
Rev Counter Fault
by kiwi » Sat Oct 01, 2011 10:04 am
First post
So the new addition has a fault with the tacho and when I picked it up the previous owner said it does not work, well all the way home it di not but...
Last post
/\WHS.
2 Replies
198 Views
Last post by docchevron Sun Oct 02, 2011 2:11 am
Rear Arm interchangability??
by DomRobinson » Sat Oct 01, 2011 12:51 pm
First post
Having avoided rear arm bearing changes in the past, by stripping entire rear subframes out of small Pugs and Fiats, AX's etc, I wonder if the same...
Last post
Oh yeah, ABS. Forgot about that. To be avoided at all costs! Looks like I'm going to have to bite the bullet and do it properly...
5 Replies
324 Views
Last post by RxBX Sat Oct 01, 2011 4:42 pm
Invoice Times
by kiwi » Fri Sep 30, 2011 11:22 am
First post
Any one able to tell me what the expected invoice time for changing a Cambelt on a Diesel would be?
Last post
The only tools I had to borrow for the cambelt job were a 16mm deep socket for the engine mounting, and a bloody great breaker bar to undo the...
9 Replies
680 Views
Last post by Dollywobbler Fri Sep 30, 2011 8:29 pm
Hoses and other things
by Philip Chidlow » Mon Sep 26, 2011 4:42 pm
First post
Can anyone supply a diagram illustrating the water hoses for a 19 n/a because I have a few and I might have access to more, but identifying them is...
Last post
erm, do you need this;
1 Replies
198 Views
Last post by Vanny Wed Sep 28, 2011 7:45 pm
Coolant warning light (orange)
by Turbo Killer » Mon Sep 26, 2011 4:42 pm
First post
The first temperature warning light has started to light up after a mile or so, i replaced the sensor and cleaned up the big brown connector block on...
Last post
That sounds a very plausible answer - the sensors for the warning lights are about 1 longer (externally) than the sensor for the gauge.
8 Replies
478 Views
Last post by mat_fenwick Wed Sep 28, 2011 9:43 am
Boot struts
by robt » Tue Sep 27, 2011 9:50 pm
First post
Does anyone know whether these struts from a Xantia will fit an estate BX?
Last post
Hi bud,
1 Replies
217 Views
Last post by Mothman Wed Sep 28, 2011 5:38 am
strange R/H driver's side suspension response
by maxgreenwood » Wed Sep 28, 2011 12:15 am
First post
Since i fitted my re-con struts from Pleiades, the driver's side front suspension is not quite what it should be.
Last post
Apart from anything obvious fouling it by inspection, check the centering of the bar in case it has moved over to it's limit one side and is...
3 Replies
209 Views
Last post by Way2go Wed Sep 28, 2011 12:29 am
ABS warning light
by johnt » Mon Sep 26, 2011 8:47 pm
First post
Hi Guys some help with an ABS issue on my GTi Thanks
Last post
Hi Jabba
3 Replies
324 Views
Last post by johnt Tue Sep 27, 2011 8:55 pm
Water pump impeller size
by Dollywobbler » Mon Sep 26, 2011 10:22 pm
First post
Sorry to bang on about this (see cambelt change in FAQ section) but much as I trust Mr Fenwick, I wouldn't mind more opinions - especially as I'm not...
Last post
You might find that originally two different engines had two different pump designs (because one had a more restricted orifice for the pump to mount...
1 Replies
169 Views
Last post by Kitch Mon Sep 26, 2011 10:44 pm
Hydraulic pump failure.....
by Kevin B » Mon Sep 26, 2011 6:23 pm
First post
Today when driving back from the MOT station of all places, and just congratulating myself on another year of BX motoring, I saw the stop light come...
Last post
A simple way to make sure is to take the hose off the reservoir end, lift as high as possible, fill it with fresh LHM and start the engine. If it was...
3 Replies
284 Views
Last post by rmattila Mon Sep 26, 2011 6:59 pm
Symptoms,effects and prognosis
by kiwi » Tue Sep 20, 2011 1:02 pm
First post
I have this feeling the TZS engine after 235,000kms and having had its head replaced 3 years and 32k ago may well be about to cause more trouble....
Last post
certainly giving all the symptoms of a failed HG yeah..
5 Replies
376 Views
Last post by docchevron Mon Sep 26, 2011 2:51 am
Front Height Corrector
by kiwi » Sun Sep 25, 2011 9:19 am
First post
Greeted by a couple of damp patches on the garage floor and disscovered yet again the Operational return (thats the one with the hose clip) has a bit...
Last post
Some how I got it done but lets just say I made some modifications on the way.
2 Replies
247 Views
Last post by kiwi Mon Sep 26, 2011 1:20 am
Driveshaft woes
by DomRobinson » Sat Sep 24, 2011 9:36 pm
First post
I've owned an H reg TZD for a year, and its generally beyond reproach; however, with a 100 mile a day commute, thought I'd treat her to a new cambelt...
Last post
The shaped tool I made is like about 2ft long 1/2 x 3/4 bar, then another piece of 1/2 x 3/8 bent into a U the hard way, the internal dims of which...
6 Replies
449 Views
Last post by philhod Sun Sep 25, 2011 9:22 pm
Magneti Marelli coil/distributor,
by Mike Holdstock » Sun Sep 25, 2011 7:06 pm
Been a long time, with many smooth BX miles.
0 Replies
295 Views
Last post by Mike Holdstock Sun Sep 25, 2011 7:06 pm
19TZD Clutch Cable Question
by Tim Leech » Sun Sep 25, 2011 4:08 pm
First post
I went to change the clutch cable on the TZD today as the clutch is very stiff, when I disconnected the gearbox end and slid it back and forth it to...
Last post
If a new cable doesn't fix the problem it may be the clutch itself. Back when these cars were still fairly new there was a mention in Citroenian that...
5 Replies
311 Views
Last post by citsncycles Sun Sep 25, 2011 5:43 pm
Floppy wiper.
by Dollywobbler » Sat Sep 24, 2011 7:06 pm
First post
The windscreen wiper on the Mk1 threatens to start cleaning the bodywork when it rains. I'm presuming this is due to horrific spindle wear - also a...
Last post
This is the method I used.
7 Replies
426 Views
Last post by Brian Sun Sep 25, 2011 4:02 pm
Oily air filter
by Paul296 » Thu Sep 22, 2011 9:36 pm
First post
I've just replaced the air filter in my car with a K&N. When we removed the old one (well, when Mulley removed it!) it was covered in oil at one end...
Last post
Off topic, sorry but what do you use for light when you're working outside at night?
14 Replies
609 Views
Last post by rmattila Sat Sep 24, 2011 7:50 am
jerky when accellerating
by fnukyguy » Wed Sep 21, 2011 8:04 pm
First post
I have a citröen bx 91 millesime... (bx 16 engine)
Last post
Try also cleaning the contacts on the inside of the distributor cap, or a new one.
5 Replies
454 Views
Last post by Paul296 Fri Sep 23, 2011 8:17 pm
dented speedlines..
by themildbunch » Wed Sep 21, 2011 6:08 pm
Finally got my tyres swapped over to a new set of the smaller width speedlines I bought through the forum here:
0 Replies
312 Views
Last post by themildbunch Wed Sep 21, 2011 6:08 pm
Knocking engine and burning oil when hot
by maxgreenwood » Tue Sep 20, 2011 12:23 am
First post
I have mentioned my noisy engine here already and the garage said it was 'crankshaft rumble' and not to worry about it, but now i'm not so sure they...
Last post
Did Leobx16v get rid of the engine/'box from his crashed valver? Would make an interesting conversion especially with carbs replacing the efi system....
28 Replies
1383 Views
Last post by mds141 Wed Sep 21, 2011 4:53 pm
Which octopus?
by ginger dave » Wed Sep 21, 2011 10:50 am
First post
Need to change the octopus on my E reg.16 re .manual,non power steering.Problem is cars 600 miles away in France and i want to be sure i have the...
Last post
May be of some help?
1 Replies
268 Views
Last post by Tim Leech Wed Sep 21, 2011 11:49 am
Changing ignition barrel
by mds141 » Mon Sep 12, 2011 8:38 pm
First post
As subject reads need to change over the ignition barrel on the valver due to it having given up the ghost. Easy DIY job? Any tips most appreciated....
Last post
New ignition switch fitted today at Dave Ashworth's in Blackpool for £20. Thanks for replies and advice guys. :)
11 Replies
549 Views
Last post by mds141 Thu Sep 15, 2011 6:24 pm
What am I leaking?
by Willy » Wed Sep 14, 2011 2:34 pm
First post
Whenever I park up after a decent drive, I seem to get a very small puddle of fluid appear under my gearbox end. Maneuvering the car in and out of...
Last post
I thought the level plug was the one on the right of the last picture?
6 Replies
479 Views
Last post by rmattila Thu Sep 15, 2011 5:09 am
Alternator problems?
by Mothman » Sat Jul 16, 2011 3:21 pm
First post
Coming back from Looe early this morning the windscreen wipers started to move slower and slower. Windows were the same and lights started to dim....
Last post
Typical innit?
18 Replies
833 Views
Last post by Mothman Tue Sep 13, 2011 9:40 pm
Clutch Cable Fitment
by Tim Leech » Sat Sep 10, 2011 6:13 pm
First post
I have a new old stock genuine clutch cable, part number 95162700, im hoping it will fit my 19TZD?
Last post
Surely that's due to the clutch pressure plate & mechanism, not the cable? :?
12 Replies
651 Views
Last post by Tim Leech Tue Sep 13, 2011 7:48 pm
door hinge panel finally rusted through..
by themildbunch » Mon Feb 07, 2011 10:28 pm
First post
Ummm, hoped this would last until the summer but the door strap panel has finally pulled away from rust that was holding it in the picture above. The...
Last post
this ISN'T going to rust again!
30 Replies
2001 Views
Last post by KevR Mon Sep 12, 2011 1:50 pm
Diesel leak...
by Philip Chidlow » Tue Aug 30, 2011 1:26 pm
First post
My TXD has decided it's going to start leaving a little patch of diesel when parked up. It's under the sump, fuel pump side. I can't see where it's...
Last post
Hi
26 Replies
1161 Views
Last post by Philip Chidlow Mon Sep 12, 2011 11:18 am
Waxoyl question
by KevR » Thu Sep 01, 2011 10:08 am
First post
I've just discovered a 10 litre tin of Waxoyl at the back of the shed. God knows how long it's been there. The solvent has all evaporated off,...
Last post
You can put the waxoyl on pretty much anywhere except brakes and exhaust.
5 Replies
1121 Views
Last post by KevR Sun Sep 11, 2011 11:55 am
Cooling System
by kiwi » Sun Sep 11, 2011 12:16 am
First post
Just hope I can describe this well in writing.
Last post
Try removing the thermostat and see if this helps if you havnt a spare one.
3 Replies
243 Views
Last post by Mothman Sun Sep 11, 2011 7:59 am
Forum permissions
You cannot post new topics in this forumcannot reply to topics in this forumcannot edit your posts in this forumcannot delete your posts in this forumcannot post attachments in this forum
