CV removal
Replies: 6
by artic-steel » Sun Jun 18, 2006 5:51 pm
First post
How do i get the CV off the driveshaft to replace the boot?, i can't see or feel a circlip.
Sorry for the basic questions but i'm new to this &...
Last post
I can feel a BX friendship coming on!
6 Replies
498 Views
Last post by tim leech
Sun Jun 18, 2006 8:38 pm
GTI wiring diagram
Replies: 2
by
sleepy0905 »
Sun Jun 18, 2006 5:56 pm
First post
Hi has anyone got a wiring diagram for a 1991 GTI that they can scan and send me by email.
sleepy
Last post
Have you had a look at Bob Smith's site - most relates to 16 valves but i don't see that that's very different.
2 Replies
343 Views
Last post by jeremy
Sun Jun 18, 2006 7:14 pm
BX19 RD Leak in hydraulic system
Replies: 7
by
Harvey »
Sat Jun 17, 2006 7:34 pm
First post
My BX19 RD estate has served me well for more than ten years, and I am loth to scrap it, but it has now developed a hydraulic leak. This appears to...
Last post
The Octo is the bunch of pipes running along the chassis leg. They run from the LHM tank to a connection point at the base of the height corrector,...
7 Replies
774 Views
Last post by Mr B
Sun Jun 18, 2006 1:24 pm
Yellow, not green
Replies: 3
by
BackinaBX »
Sat Jun 17, 2006 8:23 pm
First post
I was checking over all the fluids yesterday... and noticed that my LHM has taken on a distinctly yellow tinge.
Time for a change, do you think?...
Last post
:D :D :D
It's so peaceful down there !
3 Replies
430 Views
Last post by ellevie
Sat Jun 17, 2006 9:22 pm
K1G / 150C engine Interchangeability
Replies: 1
by
tissaoui »
Sat Jun 17, 2006 1:31 pm
First post
I have an old BX (1986) with a 150C engine that is almost dead, can I replace it by the newer post 1988 version (K1G)? What would I need to replace?...
Last post
Front subframe (!)
Weld on a new type engine support (car's) LHS inner wing top at strut.
Engine
Air filter box & ducting
Coolant hosing
Gearbox...
1 Replies
329 Views
Last post by AndersDK
Sat Jun 17, 2006 5:22 pm
coolant
Replies: 5
by
citroen7 »
Fri Jun 16, 2006 4:14 pm
First post
changed the radiator on the xantia at the weekend after much fiddling and reading of various threads and was shocked to see the botom 3 rows just...
Last post
Its best to put too much antifreeze in that not enough though?I want to flush the 16v and the xantia before winter,
5 Replies
543 Views
Last post by tim leech
Sat Jun 17, 2006 10:34 am
Stupid question time.....
Replies: 5
by
cavmad »
Fri Jun 16, 2006 11:20 am
First post
...are these clocks 140mph ones? Silly question because they are mine, but I`m stuck at work and too dim to remember! They were off a 1.9TGD estate,...
Last post
ive got a petrol console with a diesel tacho no problems, and the old car had a diesel dash with a retro fitted tacho, dont think it makes too much...
5 Replies
570 Views
Last post by Vanny
Sat Jun 17, 2006 12:11 am
B*ll*cks :(
Replies: 9
by
cavmad »
Thu Jun 15, 2006 8:00 pm
First post
Saw a pool forming or formed under my BX last couple of days and did the usual bloke thing and ignored it, hoping it was from someone else`s car.
Was...
Last post
Oops! sorry for scaring you cavmad.
I must of misread your post as I know the octopus is on the drivers side.
Cheers
Luke
9 Replies
718 Views
Last post by Toddman
Fri Jun 16, 2006 12:51 pm
Brake calliper issues!
Replies: 5
by
adamskibx »
Sun Jun 11, 2006 11:22 pm
First post
Ive got a problem with my BX that has rendered it off the road for the next few days at least. Noticed a strange sound when braking at high speed or...
Last post
Resolved! New caliper (well, reconditioned by the looks of it), and flexi pipe. However the pipe didnt screw in all the way. I didnt tighten it to...
5 Replies
727 Views
Last post by adamskibx
Thu Jun 15, 2006 11:15 pm
Diesel pump trouble
Replies: 10
by
Vanny »
Sun Jun 11, 2006 7:00 pm
First post
for a good 6 month now i've been going through a long winded process of having to prime the fuel system to start the car. Obvious thing to check was...
Last post
GET THE HELL OUTTA MY HEAD
picked it up about an hour ago at the local factors :D Have a big long length of fuel pipe too, just need to find...
10 Replies
1086 Views
Last post by Vanny
Wed Jun 14, 2006 4:10 pm
Aircon DIY Regassing
Replies: 5
by
Way2go »
Tue Jun 13, 2006 1:36 am
First post
Has anyone tried these aircon gas replenishers from Halfords? They cost $30 ish for the can containing R134a gas and oil, including a pressure guage...
Last post
If it's any help, I just had my BX's AC regassed - the guy put a UV dye in last time so was able to deal with the leaks - needed new 'O' rings - this...
5 Replies
649 Views
Last post by Philip Chidlow
Wed Jun 14, 2006 11:34 am
STOP! Red light of doom... suggestions please
Replies: 11
by
BackinaBX »
Sun Jun 11, 2006 4:31 pm
First post
Hello once again forum... this time it's a question about the fabled red light of doom...
Today (hot and sunny) I was coming up a long and steep...
Last post
Good point Dave ? Also verify that the correct lead is fitted to each temp sensor.
The lights are easily checked by earthing each connector on the...
11 Replies
1409 Views
Last post by Jaba
Tue Jun 13, 2006 6:31 pm
More aircon problems
Replies: 9
by
Jaba »
Sun May 21, 2006 9:59 pm
First post
My aircon is playing up too.
It seems to work normally for up to the first hour and then the air temperature at the vents quickly rises to ambient...
Last post
Dunno, but you can hear it on my Xantia when the A/C is running now I've put some more gas in it - needs more yet though. I'm ignoring it.....
9 Replies
1088 Views
Last post by RichardW
Tue Jun 13, 2006 1:41 pm
Brake pipe temporary repair ?
Replies: 15
by
ellevie »
Sat Jun 10, 2006 12:14 am
First post
As a result of replacing my trailing arm bearings, the brake pipe on one side near the calliper has started to seep at a particular rust spot. The...
Last post
Mr ellevie -
There is no plastic padding or other 2-component filler product that can/will withstand the Citroen hydraulic system pressure of some...
15 Replies
1697 Views
Last post by AndersDK
Tue Jun 13, 2006 12:41 am
Trailing Arm Bearings --- Outer Race Extraction Tip
Replies: 12
by
ellevie »
Sun Jun 11, 2006 11:12 am
First post
Trailing Arm Bearings --- Outer Race Extraction Tip
Jon Wood describes how to go about changing your trailing arm bearings in the DIY section --- As...
Last post
That’s a good point about the wear not being spread evenly amongst the needles. To spread the wear more evenly, you could make sure to rotate the...
12 Replies
1266 Views
Last post by ellevie
Mon Jun 12, 2006 11:12 pm
Spheres
Replies: 4
by
Ian_Fearn »
Mon Jun 12, 2006 7:36 pm
First post
I'm going to be replacing all the spheres on my TZD and i thought i'd ask for some advice on whether to go with GSF supplied Amtex spheres or...
Last post
Now that you mention the brands, IHFS rings a bell! AS I said, they seem ok.
4 Replies
799 Views
Last post by richard
Mon Jun 12, 2006 10:29 pm
BX back to origianl dealers to get some things for it!
Replies: 26
by
adamskibx »
Thu Jun 01, 2006 11:35 pm
First post
(Please note: Aircon is now sold.)
They seemed a bit suprised that I took it back there, but I went to ask them if the paint code's shading was...
Last post
Overboost indicators - if Revue Technique is to be believed, they were fitted to the very earliest Turbodiesels, then deleted.
26 Replies
1935 Views
Last post by DLM
Sun Jun 11, 2006 9:30 am
Fumes and running rich?
Replies: 11
by
Philip Chidlow »
Fri Jun 09, 2006 10:33 am
First post
My BX has quite a few miles under its belt and would benefit from the valve seals etc. being done. It does use a bit of oil and it sometimes will...
Last post
What you need is a convertable!
11 Replies
999 Views
Last post by tim leech
Fri Jun 09, 2006 6:29 pm
Hydraulic system check/analysis:strange symptoms
Replies: 3
by
adamskibx »
Thu Jun 01, 2006 11:07 pm
First post
Right: Ive got no problem as such, but this BX confuses me. Something needs replacing in th hydraulic system but I cant work out what. In other BX's,...
Last post
Sounds like a reasonably healthy one - though you should also note when making comparisons that your old blue estate was one with a very recent...
3 Replies
597 Views
Last post by DLM
Fri Jun 09, 2006 1:54 pm
'89 n/a 19 diesel (Bosch) black smoke.
Replies: 8
by
AndersDK »
Wed Apr 26, 2006 7:27 pm
First post
The good old simple diesel setup :lol:
This is my s-i-l's diesel which has gradually become worse in creating black smoke and hesitating in power...
Last post
Otherwise you can adjust it the expert's way - mark its position, slacken the mounting bolts a touch and move it say 1mm from the mark (top of body...
8 Replies
1060 Views
Last post by jeremy
Thu Jun 08, 2006 11:37 pm
Auto box fluid level
Replies: 10
by
Philip Chidlow »
Tue Jun 06, 2006 2:56 pm
First post
Hi
After having ignored it for ages, because it works (!) I thought I'd check my Auto box transmission fluid level via the dipstick. It was warm,...
Last post
I have never and will never suggest an oil additive for an engine; 2 completely different kettles of fish, but even the most sceptical will agree...
10 Replies
814 Views
Last post by AlanS
Thu Jun 08, 2006 4:40 am
Can they fail it on this?
Replies: 11
by
BackinaBX »
Sat Jun 03, 2006 12:38 am
First post
It's almost MOT time for the beloved BX... I think I have got everything that it could fail on done, but I am worried about a light.
I don't have a...
Last post
hmmm, Ok, well the 2cv does not have a tell tale dash bulb for dip, main, or the indicators, and they pass the MOT Ok (provided that everything else...
11 Replies
1301 Views
Last post by Terry Brooks
Wed Jun 07, 2006 11:54 pm
4x4 has failed its MOT (NOW MOT'D)
Replies: 15
by
Ian_Fearn »
Wed May 31, 2006 5:39 pm
First post
Thanks to Tim Leech for the MOT.
Unfortunately its failed on:
the headlights aiming too low
carbon monoxide emissions 4% (max is 3.5%)
CV boot...
Last post
Billy, this dentman normally charges fifty quid for the whole car. I paid quite a bit less than that but it was because he was already at Tim's...
15 Replies
1718 Views
Last post by Ian_Fearn
Mon Jun 05, 2006 9:35 pm
Technique passed to me by a citroen Mechanic
Replies: 3
by
sleepy0905 »
Sun Jun 04, 2006 10:41 am
First post
Hi all thought i would pass this on after talking to a mechanic, Right all those glued on pannels on the bx especially the smoked windows on the c...
Last post
I give that the thumbs up 8)
Thanks for sharing Aaron
Cheers
Luke
3 Replies
556 Views
Last post by Toddman
Mon Jun 05, 2006 12:42 pm
BX TZD Driveshaft Question
Replies: 6
by
roscoe »
Sun Jun 04, 2006 9:13 am
First post
I have pulled my 16V parts car apart and the front driveshafts in it are in better shape (CV joints, center bearing), than my TZD ones. I'd like to...
Last post
Thanks for that Dave - one less thing to worry about. Now to get the control arms off when the rain stops (funny how a drought breaks when you need...
6 Replies
698 Views
Last post by roscoe
Mon Jun 05, 2006 1:39 am
Front hub nut
Replies: 22
by
Ian_Fearn »
Fri Jun 02, 2006 4:39 pm
First post
whats the best way to get the 36mm nut off the driveshaft?
My breaker bar wont shift it.
Last post
I have a 3/4 drive socket set with a 35 mm socket - also made up a piece of 2 x 1/2 flat bar about 4' long to hold the wheel from moving. Drilled two...
22 Replies
1788 Views
Last post by roscoe
Sun Jun 04, 2006 12:55 pm
New symptom with the car!
Replies: 5
by
Cornishbx16v »
Sat Jun 03, 2006 1:18 pm
First post
hello chapps!! have finnally manages to shift the stuck tensioner bolt thats been holding me back for a while and got the old belt on for testing...
Last post
I'm sure the valves will be bent - just think of the angles they work at ant the relative position of the piston. Good news is that the valves take...
5 Replies
570 Views
Last post by jeremy
Sat Jun 03, 2006 11:09 pm
Gearbox oil
Replies: 2
by
Ian_Fearn »
Sat Jun 03, 2006 1:56 pm
First post
I'm assuming once my driveshaft is out i'm going to loose some fluid.
What should i fill it back up with and where is the filler?
Last post
I've done it now and it was the offside so i lost no oil.
My gearbox is basically the same as a 2wd one and shares its oil with the diff.
The...
2 Replies
472 Views
Last post by Ian_Fearn
Sat Jun 03, 2006 7:14 pm
HP Pump...
Replies: 27
by
BackinaBX »
Tue May 30, 2006 7:26 pm
First post
Hello again forum,
Moving on from the steering funnies, it transpires that I need a new HP pump. Now, I can get a recon one for about £140... but I...
Last post
BX obsession should just about do it !
I'd say that's about the size of it! :lol:
You need a vice that has at least a 4 jaw opening, and is...
27 Replies
2272 Views
Last post by DavidRutherford
Fri Jun 02, 2006 11:32 am
Tank Hose
Replies: 5
by
Widgit »
Thu Jun 01, 2006 6:36 pm
First post
I think I have finally found the cause of my hit/miss steering performance on my 1.7 Turbo D BX estate.
I was fitting a s/h HP pump when I noticed...
Last post
It's worth noting that any hose that is rated as oil, petrol or diesel hose is fine with LHM, as these are all mineral derivatives.
Heater hose is...
5 Replies
619 Views
Last post by DavidRutherford
Fri Jun 02, 2006 12:21 am
Steering Funnies... getting worse. Oh dear.
Replies: 15
by
BackinaBX »
Sat May 27, 2006 8:36 pm
First post
Hello forum, perhaps you can throw some light on my steering funnies.
With a cold engine, or at least until the LHM has warmed up, my power steering...
Last post
Ah, oh... I see. Well, there you go. All sorted out. Back in a BX sort of does what it says. I used to have a BX years ago - way back in 1996, when...
15 Replies
1641 Views
Last post by BackinaBX
Thu Jun 01, 2006 11:13 pm
I'm glad that's been cleared up!
Replies: 9
by
Oscar »
Fri May 26, 2006 1:34 pm
First post
Oh dear, there I was thinking it was difficult. Well, isn't the internet a wonderful thing.
Do people actually fall for this stuff, do you think?...
Last post
Don't really think petty crims make a risk assessment. I was listening to a magistrate and a criminologist on the radio the other day. The mag said...
9 Replies
1021 Views
Last post by Oscar
Wed May 31, 2006 2:32 pm
xantia heater fan
Replies: 7
by
citroen7 »
Sat May 27, 2006 10:21 am
First post
yes i know it is not our beloved bx but i see quite a few members have xantias and was wondering if any problems had occurred with the heater fan and...
Last post
I just followed anders advice in your link to use the supply from the grey plug as long as it gets wifey of my back it must be a result!!
7 Replies
669 Views
Last post by citroen7
Wed May 31, 2006 12:54 pm
Missing Fob buttons (AKA crap technologies)
Replies: 9
by
Gareth Wales »
Thu May 25, 2006 8:42 am
First post
I have two working Piranha Alarm fobs - well they work when I activate them by a bent 1 nail that I carry around.
The alarm itself is excellent, the...
Last post
Hehe!
9 Replies
688 Views
Last post by tim leech
Tue May 30, 2006 5:53 pm
6 Replies
568 Views
Last post by sleepy0905
Fri May 26, 2006 10:23 pm
A plea for help!
Replies: 25
by
Kitch »
Tue May 16, 2006 12:14 am
First post
Rear arm bearings:
My 16v needs the O/S doing and the GT I just picked up needs the pair doing.
I need to learn how to do this....I'm asking to find...
Last post
Thanks for all help.
I took the GT to David R's last weekend (a thoroughly nice guy too). He helped/did all the work and the car rides 100times...
25 Replies
1992 Views
Last post by Kitch
Thu May 25, 2006 6:39 pm
Electric mirror
Replies: 9
by
sleepy0905 »
Wed May 24, 2006 1:11 pm
First post
Hi it is a quick question i have a o/s electric mirror off a GTI 4x4 now i have identified the wiring except there is a 2 pin connector as well now...
Last post
OK mate I wil hold on to them, let me know when you want me to post them to you etc. Unless your coming to the FCS then I will take them along for...
9 Replies
878 Views
Last post by tim leech
Thu May 25, 2006 9:34 am
Windscreen woes
Replies: 15
by
richard »
Sat May 20, 2006 4:22 pm
First post
Hi
I decided to remove some surface rust on whe panel which runs below the screen. To do this I needed to peel back the trim. Now, the screen has...
Last post
Forget what the fitters think, YOU'RE THE CUSTOMER!
15 Replies
1611 Views
Last post by Ian_Fearn
Wed May 24, 2006 9:16 pm
Exhaust CO level too high
Replies: 15
by
sleepy0905 »
Tue May 23, 2006 7:46 pm
First post
Hi can enyone help what is the best way to reduce the exhause CO level as mine is too high it should be less than 3.50 and mine is 3.91 I have...
Last post
:D Well done :D
15 Replies
1618 Views
Last post by ellevie
Wed May 24, 2006 6:09 pm
Not a BX question, but perhaps you can help???
Replies: 9
by
BackinaBX »
Tue May 23, 2006 5:18 pm
First post
Hello again forum, this one is for all Xantia owners with a keypad alarm/immob.
My dad's Xantia had developed a problem. When you turn the key, both...
Last post
Mmmm.......Mice in a Xantia :shock:
Luckily the BX just seems to suffer from spiders (webs) on the door mirrors :D
9 Replies
760 Views
Last post by Way2go
Wed May 24, 2006 4:10 pm
Camshaft Oil Seal
Replies: 1
by
finishthat »
Tue May 23, 2006 11:47 pm
First post
Hi,
new member, details in BXchat, next job for me is a camshaft oil seal,
its the pump end , currently leaving the traditional stripe on the...
Last post
The pulley normally comes off with no problem. :D
1 Replies
371 Views
Last post by ken newbold
Tue May 23, 2006 11:57 pm
BX TD sprays out coolant from header tank
Replies: 19
by
jonkw »
Mon May 22, 2006 3:28 pm
First post
I have devoted considerable time gazing into space wondering whats actually wrong with my car, and noted the following:
1) When the donk was in the...
Last post
I think, that it was 3L of antifreeze, and the rest is water, last time I did it.
The waterways that I have had off recently appeared pretty good,...
19 Replies
1928 Views
Last post by jonkw
Tue May 23, 2006 11:14 pm
I know it isnt a bx but
Replies: 13
by
sleepy0905 »
Sun May 21, 2006 5:23 pm
First post
Does anyone know how the instrument pod comes out on an AX as linda`s needs a new cable and i cannot find anything on the AX club site as the robbing...
Last post
If anyone is off to FCS and is in the sort of M6 coridor bit of lancashire from Manc to Preston and can meet up with me to pick up a wheel for sleepy...
13 Replies
1316 Views
Last post by M
Tue May 23, 2006 9:35 pm
Checking coolant levels - without the stick!
Replies: 9
by
BackinaBX »
Fri May 19, 2006 5:11 pm
First post
Hello again forum,
Because I've only just bought my shiny BX, I am of course spending too much time going over it finding out how stuff works and...
Last post
I always use de-ionised water as down here in Suffolk the water is so hard you get threatened everytime you turn the tap on :lol:
So i'm hoping...
9 Replies
1075 Views
Last post by Bluey1978
Mon May 22, 2006 10:41 pm
Land Rover starting q
Replies: 16
by
Oscar »
Mon May 08, 2006 1:25 pm
First post
Hello
I'm posting this more in the spirit of enquiry than anything else, and I know we have a few LR fans.
A friend of mine has bought a 2nd hand...
Last post
That is a Freelander.
I'd been working under the assumption that this was actually a proper Land-Rover, rather than a freelander.
Which does only...
16 Replies
1618 Views
Last post by DavidRutherford
Mon May 22, 2006 4:10 pm
Biodiesel Wisdom?
Replies: 10
by
Stewart (oily!) »
Sat May 20, 2006 6:27 pm
First post
The ZX TD has been needing its bulb squeezing again in order to start of a morning, I replaced all of the leakoff pipes, nothing, then I looked at...
Last post
:-s I'm not implying dinodiesel is defective in the lube department [-X :), just that biodiesel has better lubricative qualities. Whatever is...
10 Replies
973 Views
Last post by ed4ferrets
Mon May 22, 2006 10:08 am
Carb maladies
Replies: 3
by
mnde »
Fri May 19, 2006 1:02 pm
First post
Hi all,
My BX has recently developed a couple of niggles.
1) When I start the car, the engine will run for about 5 seconds, then die - even if I...
Last post
The spit at standstill is interesting. What is happening I think is that a plug is sparking and lighting mixture left in that cylinder - and the...
3 Replies
442 Views
Last post by jeremy
Sat May 20, 2006 9:54 am
Which adhesive ?
Replies: 12
by
Gareth Wales »
Sun May 14, 2006 10:15 am
First post
I want to fix new rubbing strips but wonder which is the best way - would a heavy double-sided tape work? Cit used a black mastic-type adhesive. I...
Last post
With windows and side strips, the sikaflex being black is quite inobtrusive but it stands out like dogs b***s if used in a headlight, so I've usually...
12 Replies
1266 Views
Last post by AlanS
Thu May 18, 2006 12:45 pm
Onlinr Paint colour chart for BX.
Replies: 8
by
AlanS »
Fri May 12, 2006 8:07 am
First post
I know there's one somewhere; I thought it was on Gabors DIY site, then I tried CitroenZ but I can't find it on Brij's then I went Citroenet again no...
Last post
I must be drinking my own bathwater with this, but the guy concerned doesn't seem to be able to find a paint code on his car and I'm sure I found one...
8 Replies
835 Views
Last post by AlanS
Thu May 18, 2006 5:06 am
Anyone knows this injection pump?
Replies: 19
by
pitman »
Sat May 13, 2006 11:05 pm
First post
I was wondering if anyone knows this injection.
It's in a BX Leader 19 Diesel, Mk1, ORGA-Nr. 3455 (25.04.86).
BTW, I got also a funny fuel...
Last post
Mahle, Motorcraft, Purflux, Bosch ... you name it and they would all have a filter.
I believe there is as many different manufactures of oil & fuel...
19 Replies
1733 Views
Last post by AndersDK
Wed May 17, 2006 10:54 pm
Forum permissions
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum