recently my Bx's heating fan has stopped working for most of the time, but sometimes it still decides to come on, which makes me think that the motor...
Last post
Having pulled all the blower and control system completely apart just recently, there is nothing that is inaccessible like on some cars. The Citroen...
Hi All. I bought my Citroen BX over 6 years ago & only recently realized this forum existed.
After reading through a few posts & seeing how...
Last post
With regard to the ratio changes, during my visit to Kieran's last week, his Dad mentioned that they onced dropped a 19NA engine into a TD car (using...
Anyone got the seal specification for the above mentioned part?. B2C engine and the only real leak is from under the distributor. Tried searching but...
Last post
seems there is only one O ring across both makes of DIZZY
I'm hoping someone might be able to help me. My speedo is not working. Initially it was diagnosed that it was the cable that was the problem. I have...
Last post
this part No. crosses over to all these models on an all families search
2649 04
1 document(s) found for BERLINGO
1 document(s) found for ZX
1...
Looking back on topics it would seem it is the top or dash end of the double cable that tends to fail. Having parted mine into halves while visiting...
Last post
All top cables are the same just the bottom cables vary depending on engine fitment.
The complete speedo cables on the BX 4x4's are different, (or...
searching the net for rear box t/d hatch, seems a lot listed but confusing, would i be right in assuming there are basically 2 back boxes, flange and...
Last post
Not sure whether the TD front pipe would fit the NA manifold - I welded the NA front pipe to the TD centre pipe on mine!
I know rear Xantia rams cvan be adapted to fit a BX, but what about front struts? I ask as I've got the chance to buy a brand new Xantia one.......
Last post
at least the strut/leg return pipe will not be an issue,
as the two on the BX one is a seepage return and the other is just a vent, so you could just...
Strange little one. Started car, drove off, turned on wiper Oh its not working!. Water in the relays again - no. Turned out the 3 or 4 position...
Last post
It is probably the plastic return spring retainer that has cracked and failed. It is the same diameter as and sits in the inside end the lock barrel....
Hello again
Doing some work on my BX before the winter sets in
The car has been standing a while due to a leaky radiator and low working spirits, and...
Last post
or just apply diesel fuel, very very good penetrating fluid,
regards malcolm agreed diesel is an excellent penetrate, so why does no-one sell it in...
Here's one for the diesel experts. I know the Red One is a 'poor' starter because I've got the white one to compare it with. That one will start when...
Last post
Wouldn't different types of batteries with different CCA ratings make a difference to starting performance?
I had to RAC the White One back from Hampshire last month (see Mothman's blog.) due to an ongoing hydraulic leak. When the patrol guy turned up he...
Last post
I've got a scissor jack that has a slot in the top that fits the original centre point quite well that I carry in the back of the car for use on the...
I have a 16V bodykit I saved from a scrapper, it was nailed onto an 8V with so much mastic I gave up trying to remove the front wing pods at the time...
Last post
There were no after market versions of the 16v kit - they're all fibreglass (including the bumpers on the ph2).
have purchased 2 handbrake cables off the bay £5.48 each from mr auto united kingdom, they are based in lyon, france, the cables are made by BOLK yes...
Last post
2 handbrake cables arrived today in a huge box from france, they look ok made by TRW pt/no GCH1049 will be fitting them on the TGD this week, will...
noticed over the past few weeks that the steering is starting to wander a little, have had a quick check of lower arm bushes, tie rod ends and all...
Last post
i have today replaced the lower ball joint, cleaned and lubed the calipers, new pads, replaced the split ball joint rubber, 2 new handbrake cables, 2...
Right then, I still NO power steering. I believe all was mechanically sound before I got the car, so it must be something either due to storage or me...
Last post
Yay! Think I found the culprit, and, feeling rather smug in my smugness, I actually diagnosed something by reading, re-reading and finally...
Haven't been on here for a bit, but yesterday we replaced the octopus on the TZD turbo. It seems to be ok now but then we discovered another leak......
Last post
i think if you gave ten people this same challenge, and not letting any of then in on what the others was attempting, the outcome would be very...
The pinion on the BX rack is leaking - it has been for about 3 years - but as its now dropping hydraulic fluid everywhere the time has come to do...
Last post
Strange you are contemplating the steering job as we have just had a reconditioned pinion fitted today to stop a major leak ( well it looks like that...
Now that GSF no longer stock 1.6 (1.4 and presumably 1.9 petrol) front spheres, which are the best replacements? I note the AEP Direct ones are...
Last post
Took the plunge and fitted a pair of the IFHS ones from Aep. We now have suspension. V disapointed with the Amteks from GSF they must have been near...
How is the splitter attached to the front bumper ? and I'm looking at getting some new headlights as the reflective surface inside the current ones...
Last post
I just used a hacksaw blade - it must be easy as even I can do it. It's also a good idea to use a small screw just to secure them as - after 20 years...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
