Hello all, I want to change over the front seats
on my bx , is it done from inside the car.
thanks all.
Last post
My experience so far has been that most Mk1's use allen or cross head screws and bolts where Mk2's use Torx, although there does seem to be a bit of...
Hi all I would like to learn how to do a coolant change on my TZD at home but don't really know the first place to start, anyone got a simple step by...
Last post
Got some holts speed flush to do the job but I just wanted to check, I undo this bottom hose
The BX of amazing tattyness is losing LHM. Not a massive amount, but enough that it needs a top up every few months. Only thing I can't tell is where...
Last post
I don't know if i'm doing pseudo-science , but the PAS vent have its tube ok? Because mine hasn't yet and i thought about that:
Just noticed diesel pouring out from the nearside rear of my BX this morning when on a camber - Very hard to see where it's coming from up there but...
Last post
When i replaced a new tank on mine, i forgot to connect the breather and i had to lower it for doing this job. I couldn't reach the breather and...
There is a definitive rumbling noise coming up through the chassis, moreso when turning left even the slightest bit, would this mean o/s/f bearing is...
Last post
Struggled for a few hours before trying to remove old bottom ball joints, id rather let someone else have the trouble for a few quid, saves knuckles,...
Took this off my spare n/a diesel engine. Its the holder for the rev counter sensor. Is it common to all diesels including the 1.7 turbo including...
Last post
That is the same as the holder that was on my engine, Some have a different holder lower down on the block (I think its the TD's), & some petrols are...
Been very happy with my BX bought on a whim from eBay, but for one problem, an oil leak that at the moment is still relatively minor....
Last post
150c engines/box shared the same sump didnt they? Crankcase to bellhousing gasket? Mine also leaked from the back of the rocker cover as the sloping...
Never rains but it poors! Well thats a good way to say suddenly getting a few bugs.
Not sure if related to the last problem but since or coincidence...
Last post
I posted this before there is no rust on these BXs not like you get in the UK due to a few factors like lack salt on the roads, being inland and high...
As some may have read elsewhere (big entry in blog to follow) I'm in the middle of changing the cylinder head on Timex. As part of this I've bought a...
Last post
Yes, these are plastic deformation bolts. Older ones that need retightening were not, I suppose.
The last two fill ups (brim to brim) as always I noted fuel consumption had gone from the reasonable (for here) 10-11 miles per litre down to 9.5 and...
Last post
Checked! I am going to see if cold weather factor and hill climbing made a huge differance. Potential those soft winter tyres played a factor as it...
Picked up a set ofg 6j wide speedlines at weekend with no tyres, so wondering what the correct size tyres are for them
Also missing 1 centre...
Last post
The French will not even test a car if it's got different size tyres to those fitted at the factory. You also need identical tyres on each axle. They...
Hello all, First thanks to all for helping me on my
sliding roof replacement, all working fine only
thing is when I lower the roof seems to go...
Last post
I think that one of the jobs on Timex while I'm underneath will be to go right through the return system - The return pipes from the rear are already...
Could anyone with access to the correct Citroen manuals please tell me if the valve springs 0952.55 are for the 1.4 litre 150 engine or the later TU...
ISTR trying the old alternator from my 1987 1.6TRS in a TZD and it didn't fit, but I can't remember why! Probably wrong pulleys. Might still have it...
..from rear near-side. Parked up asap, foolishly placing suspension lever in lowest position. Jack up, discover unable to remove wheel close to leak....
Last post
Blind guess would be strut walls too, but once you can get it in the air and peer underneath it should be evident! You can jack up the rear of the...
I'm debating whether to go to the national this sunday and if so whether to do the clutch on the 4x4 before i go? It really is on its last legs now!...
Last post
Thank you both for your advice/input, I didn't end up going to the national in the end. I haven't done my clutch yet but i'm sure it would have made...
I want to change the oil breather on my car (1.6 XU, 65 kW, BDY), so I was wondering if oil breather are same for BX 16 and Peugeot 405/309/205 with...
Last post
this part No. 118045 is not the breather its self, but just the rubber filler neck only
here is price and part No. from citroen, although it is NFP...
Is there a definitive guide to dropping the rear sub frame? I know I am going to have to deal with a little er corrosion issue to get through the MOT...
Last post
This was the main reason the tzdt was condemed by previous owner for scrap, the rear out sill had gone along with the inner sill extending up into...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
